Power steering belt diagram for 2004 sebring 4 cyclinder

1. From the top of the vehicle loosen pivot bolt Power Steering Belt Adjustment
2. From under the vehicle loosen the locking bolts F and G
3. Install the belt. Adjust belt tension with 1/2 in. breaker bar installed in adjusting bracket Power Steering Belt Adjustment
4. Tighten locking bolt G to 28 N·m (250 in. lbs.)
5. Tighten locking bolt F and the pivot bolt to 54 N·m (40 ft. lbs.)

go to www.automecanico.com translate this web with your browser
and get the topic.
God bless you

It sounds like the power steering pump has a broken pump vane and will need to be replaced and then the system flushed to get the debris out of the system so it won't ruin the new pump.

Thanks for using FixYa.

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze

Fig. Accessory drive belt routing-Chrysler 2.7L engine

2.7L Engine
A/C & Alternator Belt

1. Raise and safely support the vehicle.
2. Remove the right front wheel and belt splash shield.
3. Loosen tensioner locking bolt and pivot bolt.
4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:

1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
2. Adjust drive belt tension.
3. Install the belt splash shield and right front wheel.
4. Lower vehicle.
   
   
   

   Fig. Installing A/C & alternator belt-2.7L engine
   

1. Before servicing the vehicle, refer to the Precautions Section.
2. Raise and safely support the vehicle.
3. Remove the right front wheel and belt splash shield.
4. Loosen the tensioner locking bolt and pivot bolt.
5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:

1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
2. Adjust the drive belt tension.
3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
4. Lower the vehicle.
   

Power Steering Belt

1. Raise and safely support the vehicle.
2. Remove the right front wheel and belt splash shield.
3. Remove the air conditioning compressor/alternator belt.
4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
5. Remove the power steering belt.

To install:

1. Install the power steering belt on pulleys.
2. Adjust drive belt tension.
3. Install the air conditioning compressor/alternator belt.
4. Install the belt splash shield and right front wheel.
5. Lower vehicle.

1. The fan belt routing diagram for 2004 Volkswagen Bora 1.4 16V



2. The fan belt routing diagram for 2004 Volkswagen Bora 1.6 16V



3. The fan belt routing diagram for 2004 Volkswagen Bora 1.8 Turbo




4. The fan belt routing diagram for 2004 Volkswagen Bora 2.0



5. The fan belt routing diagram for 2004 Volkswagen Bora 1.9 TDI


CS = Crankshaft
Gen = Alternator
G = Guide pulley
T = Tensioner pulley
AC = Air Conditioning
PAS = Power Assisted Steering

Click on the following direct Link. It has the Belt Diagrams you will need, complete with Removal Diagrams and Directions. It also has numerous other helpful diagrams for use.

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!
http://www.2carpros.com/car_repair_information/year/2002/make/chrysler/model/sebring/2002_chrysler_sebring_drive_belt_routing_diagram.htm

Here is a diagram of the serpentine belt for the Maxima. I don't have instructions on power steering...

http://www.gates.com/common/part_locator/view_diagram.cfm?id=S4003

the belt will be on the front pulley on the power steering pump

you have two belts . put the large belt on first . it goes around crank pulley air conditioning pulley alternator pulley.loosen tension pulley to adjust belt. tension. then you put the other belt on power steering pump pulley and crank pulley. adjust belt tension loosen power steering pivot bolt. that it.

I can get you a diagram on monday but it goes from the alternator to the power steering pump then around the tensioner pulley then around the crank pulley then to the a/c compressor then pull on the tensioner to give you some slack and slip it on the waterpump.I hope that helps.Let me know if you still need the diagram