Drivers power seat will not move forward from full rear position.how do I access rear bolts to remove seat for repair? all seat switches work

Normally there is 4 bolts going into the floor. They are likely under a small plastic cover. Use the seat position adjustment to allow easy access to the bolts. When removing the front bolts, adjust the seat all the way back, and all the way forward when removing the rear bolts. If they are power seats, be sure to disconnect any wiring at the connectors. Then the seat just lifts out. The seat back angle can be adjusted forward if there's any problem getting it out the door.

You must remove the seat from the power seat transmission then remove the drive motor from the seat transmission, move the seat to the desired position and reinstall the motor to lock it in place. The seat transmission is bolted to the seat mounting bracket/rails.

Auto Repair: How to Replace a Power Seat Motor - YouTube

? 1:44
https://www.youtube.com/watch?v=EDh-0rs5Fjo
Oct 26, 2010 - Uploaded by automdvideos
Auto Repair: How to Replace a Power Seat Motor ... 2007 - 2008 Ford Expedition/Lincoln Navigator Driver Bottom Install Video ...2003-2006 Chevy/GMC Seat Cover Install 1 of 3 - eBay Ready ...2000 Ford Explorer Front Seat Track Stuck Motor Repair - Duration: 4:39. by cubmancan 4,959 views. 4:39.
Drivers seat is dead! No power seat or heat. - TheDieselGarage.comwww.thedieselgarage.com/.../96465-drivers-seat-dead-no-power-seat-hea...Mar 22, 2010 - 2003-2005 Chevrolet Avalanche, Silverado, Suburban, Tahoe 2003-2005.... Power seat on driver side didn't work.....passenger did! Neither ...DANG electric seat ' Chevy Truck Forum ' GM Truck Clubwww.gmtruckclub.com/forum/threads/dang-electric-seat.2990/Apr 27, 2006 - 10 posts - ‎7 authors'03 Tahoe My driver seat just stopped, of corse not where I need it, the ... I have a 2003Tahoe and both heated seats are not working. ... with my seat heater on the drivers seat in my 03 Avalanche, it turns ... The driver's side on my Silverado gets way warmer than the passenger side. ... Frozen New Member.Power Seat Problems?? - Tahoe Forum - Che

I had the same problem on my 2003 Toyota Camry. The threaded drive screws are what spin underneath the seat and cause the seat to move back and forth (same way a garage door opens or closes). When the seat gets all the way in the forward position, the threading on the drive screws ends, which causes the bolts connected to the seat to jam and get stuck. It should sound like the motor is trying to turn but it won't, it just clicks. Un-jam the bolts and rotate them one rotation from the all the way forward position to ensure your seat is reinstalled straight.

Try removing your seat bottom to access small motor that moves the seat,Tap on seat motors while holding seat switch in the forward position.

This is not necessary...as many have stated...use a hammer with switch in reverse position. Hammer the seat back...it will catch...

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

seat frame base is held to floor with four bolts, one in each corner.  Begin by moving seat to the full forward position, remove the two rear seat frame bolts, they may be covered by carpet and plastic trim.  Them move seat to full rear position and remove both front frame bolts, the seat will now be free to remove.  Keep me posted

My intuition tells me that the 6 way power seat track forward / reverse motor is bad. Sometimes you can replace just the one motor but most often a whole new power seat track is the only way to repair. It is not too bad to replace but the seat will have to be removed from the car and placed upside down to access the track assy. There are 2 bolts in the front of the seat and 2 bolts in the back of the seat that hold it down to the floorboard. Once it is loose you can rock the seat backwards to access and unplug the electrical connectors.

Had exactly the same problem. Hacked a solution, disconnected the flexible cable from the motor. Problem was the nylon drive gear was stripped. Just twisted the cable by hand to desired position ( wife's car) to fit her. Left cable detached and accessible under the seat if needed again. Big tussel getting the seat removed. GM has a very large strange torx screw holding the seat belt mount which has to be removed. Other strangeness the front 2 seat mount bolts were metric. The rear 2 were US SAE standard. Other strangness one bolt was never installed at factory ?? Was probably close to lunch time at the seat place. If you want to repair fully you should get a used ? motor as I think the wholw motor housing was rather crimped and built into th seat frame. That's probably why I did the "manual hack" works well for a year now. Now window motors are another sad story.
(inner door pannel is welded in place) need to cut for access - Dealer quited $500 - window is rather still closed.
Good Luck
Apeal