20 Most Recent 1999 Chevrolet Corvette Questions & Answers


The service and repair manual with diagram will provide you step by step help to fix the problem easily and you will get the manual from the given link https://toolsnyou.com

1999 Chevrolet... | Answered on Aug 28, 2019


Try talking the belt off and flipping it around so it rotates the other way. If the sound goes away problem solved. It sounds rediculous but it does work about 80% of the time.

If it comes back or doesn't go away you can always try replacing the belt.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

1999 Chevrolet... | Answered on Apr 06, 2019


It is either the switch or the motor.

1999 Chevrolet... | Answered on Feb 13, 2018


mourglars ??????????? What ??????

1999 Chevrolet... | Answered on Jan 02, 2018


www.bbbind.com/ free wiring diagrams .

1999 Chevrolet... | Answered on Nov 20, 2015


For What system ?

1999 Chevrolet... | Answered on Nov 15, 2015


You have to just about pull the whole dash out !


Removal Procedure




  1. Remove the front floor kick-up panel. Refer to Kick-Up Panel Replacement - Front Floor in Interior Trim.


  2. Remove the cover from the I/P electrical center.


  3. Remove the HVAC CON (HVAC controls) MiniFuse?® #27 from the I/P electrical center.


  4. Remove the I/P upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gauges and Console.


  5. Remove the instrument panel cluster (IPC) to steering column bracket retaining screws.


  6. Reposition the IPC to better access the LH temperature valve electric actuator.


Is yours manual or automatic HVAC system ? if you haven't done this before I suggest you take it to someone who has !

1999 Chevrolet... | Answered on Jun 02, 2015


I can't find a reset for that year of Corvette. It is a Passlock system. So maybe the normal 30 minute procedure will work.

Perform the re-learning procedure

  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to start the engine, then release the key to ON (vehicle will not start).
  3. Observe the SECURITY light, after approximately 11 minutes the light will turn OFF.
  4. Turn OFF the ignition, and wait 10 seconds.
  5. Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes ( the vehicle is now ready to relearn the Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK).

If not, this site may help. http://diy-gm-security.com/

1999 Chevrolet... | Answered on Jan 29, 2015


open the glove box and check to see if the lock is held in by 2 screws or a "c" clip. Remove them /it and the lock will come out . The lock/barrel and the latch tongue will be integral and will need replacing as a unit.

1999 Chevrolet... | Answered on Jan 09, 2015


I took my 99 vette to the dealer whith the same problem and they replace the rack and pinion because the black wire on top the rack was damaged.

1999 Chevrolet... | Answered on Sep 19, 2014


The blend door actuator is located on drivers of car above the gas pedal and held down with 2 or 3 5.5 mm screws good luck in a tight area.

1999 Chevrolet... | Answered on May 09, 2014

Not finding what you are looking for?
1999 Chevrolet Corvette Logo

238 questions posted

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Corvette Chevrolet

  • Corvette Chevrolet

Most Popular Question

am putting donnelli rear view mirror in

  • Cars & Trucks
Loading...