Sunroof will not close all the way

Do you know how to do automotive electrical testing ?????? How to read a wiring diagrams ???? http://www.bbbind.com/free_tsb.html .Videos on youtube Ohms Law Tech Tip from L1 with Dave Hobbs Copy of Voltage Drop Essentials TST Motor Age The only way to find the problem , testing !

Sunroof Description and Operation (One Connector System)
Sunroof
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
• Open
• Vent
• Closed
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.

Your best bet , take it to a qualified repair shop or buick dealer .

might try spraying white lithium grease on the slides and open and close few times my g6 did the same thing grease it and open and closed a few times then it work

Some sunroofs have a open switch like the drivers window. You push it and the window will open automaticly. The button on your sunroof could be jammed so even though you can close it as soon as you release it, it will auto open on it's own.

It can be faulty motor or loose wiring issue or faulty /weak sunroof controlling switch or there is some blockage for sunroof to come down to close or sunroof out of its track the headliner is out of its way.There re many possibilities.All this basics needs to be checked.For further troubleshooting,go through this help link:----
Click the link mentioned below:------
How to Manually Close the Sunroof ? http://howtobyme.blogspot.in/2012/05/how-to-manually-close-sunroof-on-2001.html

-------------
Sunroof Stuck open? http://howtobyme.blogspot.in/2012/05/2001-lexus-is300-sunroof-stuck-open.html

----------
How to manually close Sunroof on Navigator? http://technoanswers.blogspot.com/2012/01/how-to-manually-close-sunroof-on-2000.html

----------
This will help.
Thanks.

03 Jeep Liberty sunroof wont close. I have 4 sunroof buttons; Open, Close, Vent and ASC. Open and Vent buttons are working fine. Close button is not responding. ASC button is flashing red and green but does nothing when pushed. I have no way to get it closed

Do you know how to test automotive electrical circuit's with a DVOM - digital volt ohm meter ? When adjusting the moon roof did you see any switches ? sunroof limit switch
Measure the reference voltage of the sunroof limit switch soft stop signal circuit at the sunroof control harness connector to a good ground.
Does the reference voltage measure near the specified value?
4.5-5.5 V
Notice: Do not open the sunroof glass past the full open soft stop position. Doing so may damage the sunroof assembly and or the roof top.
Connect a jumper wire to the sunroof limit switch soft stop signal circuit at the sunroof control module harness to a good ground.
Turn ON the ignition, with the engine OFF.
Using the sunroof switch, operate the sunroof system, not to exceed the full open soft stop position.
Does the system operate as requested?

Do you know what a wiring diagram is ? Free one's here
http://www.bbbind.com/free_tsb.html Enter vehicle info. year ,make ,model an engine size . Under system click body & accessories ,then under subsystem click on sun roof . Click the search button then the blue link . See the control module , motor an the two switches ? One is probably miss adjusted . or bad !

Power Sunroof System Components
The power sunroof system consists of the following components:
• Sunroof control module
• Sunroof motor with the limit switches
• Sunroof switch
• Sunroof glass-spoiler type, with glass sliding above roof
• Sunshade
• Rail and track assembly upon which the sunroof glass rides
• Power sunroof system circuit breaker: PWR WDO 25 A
• Ground: G204

Sunroof Limit Switches
The sunroof limit switches track the position of the sunroof glass through two limit switches:
• Soft Stop limit switch through the sunroof limit switch soft stop signal circuit
• Vent Stop limit switch through the sunroof limit switch range signal circuit
The sunroof control module monitors the limit switches and based on the input combinations, determines the position of the sunroof glass. As a sunroof limit switch closes, the 5 volt reference will be shorted to the sunroof limit switch low reference circuit, pulling the 5 volt reference to 0 volts.
The sunroof control module monitors both sunroof switch input requests and based on the sunroof limit switch input combinations, will control an output to the sunroof motor, to drive the sunroof glass to the requested position.

Sunroof Motor
The sunroof has a bi-directional motor. When the motor is not operating both circuits are grounded. When the motor drives the sunroof glass in the direction from the closed to vent or vent to open position, the following occurs:
• Voltage is supplied to the sunroof motor open circuit.
• Ground is maintained to the sunroof motor close circuit.
When the motor drives the sunroof in the direction from the open to vent or vent to closed position, the following occurs:
• Voltage is supplied to the sunroof motor close circuit.
• Ground is maintained to the sunroof motor open circuit.
The sunroof control module is equipped with a timer circuit which stops the operation of the sunroof motor after 8 seconds.

Some customers may comment that the sunroof will no longer respond to the control switch while in a vented, partially opened, or fully opened position.
Cause A software issue with the sunroof control module may cause the sunroof control module to incorrectly indicate a "closed" position, which may result in no power to the sunroof motor.
Correction Verify the customer concern. If a condition is present, replace the sunroof control module with a new sunroof control module, P/N 15847643. Refer to the Service Procedure in this bulletin.
Service Procedure

1. Verify the customer concern by opening and closing the sunroof. • If the sunroof will not open , check the power windows. - If the power windows are also inoperative, check the fuse. If the fuse has opened, refer to Corporate Bulletin Number 05-08-64-004 to install 30A circuit breaker. - If the power windows are fully functional, refer to "Power Sunroof Inoperative" diagnostics (SI Document ID# 1392967) in the Body section of the 2005 Chevrolet Equinox or Saturn VUE Service Manual. • If the sunroof will open (or is already open), but will not close , proceed to Step 2.
2. Replace the sunroof control module. Refer to "Sunroof Control Module Replacement" procedure in the Body section of the 2005 Chevrolet Equinox Service Manual (SI Document ID# 1196049) or Saturn VUE Service Manual (SI Document ID# 1710479).
3. Open and close the sunroof in order to confirm that the customer concern has been resolved.

Parts Information Part Number
Description
Qty
15847643
Sunroof Control Module
1

I think I know the answer....your gear has slipped on the cable a few teeth. Set the roof to the desired closed position, flush with your roof. Then open the panel above the mirror by first prying off the switch plate and removing the two 10mm bolts holding the mirror. Remove the sunroof motor gear, or rather just lower it out so it is disengaged with the cables. Now connect the switch and hit the auto open button as if you wanted to open the roof with single flick of the switch. Now hit the auto close button (same button of course, but the single touch method). The motor will advance and stop to where it thinks the roof should be, closed, which it is. Reassemble the gear into the slot, test it if all good, replace the mirror and panel.
Good luck.
Manfred.

The sunroof continues to open and close normally from front to back, but the vent stays open.

you can open and close you sunroof "manually" remove the plastic cover next to your sunroof and dome light buttons (above your rearview mirror) there is an allen wrench stored inside... insert the wrench into the corresponding hole and you can close or open you sunroof by turning the wrench