20 Most Recent 2001 Oldsmobile Alero Questions & Answers


It sound like you have a gear problem in the motor need to remove motor and replace it or replace the gear

2001 Oldsmobile... | Answered on Mar 31, 2019


Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything
someone on fixya recommended it to me and I thank him even today

2001 Oldsmobile... | Answered on Feb 01, 2019


Injector clogged , plug fouled, weak coil , bad plug wire if not coil on plug , weak compression on that cylinder from bad rings, valve seat or head gasket .

2001 Oldsmobile... | Answered on Nov 15, 2018


remove and clean all cables and the battery itself,bad connection somewhere

2001 Oldsmobile... | Answered on Sep 04, 2018


No , clogged fuel filter would cause problems at higher speed , lack of power . What engine does it have ? 2.4 or 3.4 You have a sensor problem , maybe . If your vehicle has the 3.4 L V-6 it has two crankshaft position sensors A & B One is for low speed operation & one for higher speeds . I would think the 7X is bad .
The 7X CKP sensor is bolted into the center of the engine block and protrudes into the crankcase. The 7X CKP sensor reluctor wheel is cast into the crankshaft.
The 7X CKP sensor is a variable reluctance sensor. The magnetic field of the sensor is altered by a reluctor wheel that has seven machined slots, six of which are equally spaced 60 degrees apart. The seventh slot is spaced 10 degrees from one of the other slots. The 7X CKP sensor produces six pulses and one sync pulse for each revolution of the crankshaft. This signal must be present for the IC module to send a 3X reference signal to the PCM. The 3X reference is known as the low resolution engine speed signal.

This sensor is located in the side of the block .


The 24X crankshaft position (CKP) sensor (1), secured in a mounting bracket (3) and bolted to the front side of the engine timing chain cover (2), is partially behind the crankshaft balancer. The crankshaft balancer contains the 24X CKP sensor interrupter ring.
The 24X CKP sensor contains a hall-effect switch. A hall-effect switch is a solid state switching device, which produces an OFF-ON pulse when a rotating element passes between the sensor tip and a magnet. This rotating element is called an interrupter ring. In this case the interrupter ring has 24 evenly spaced blades and windows. This sensor produces 24 ON-OFF signal pulses per crankshaft revolution. The 24X signal is used for enhanced smoothness and idle stability at a lower calibrated RPM. The 24X signal is known as the medium resolution engine speed signal.

2001 Oldsmobile... | Answered on Aug 30, 2018


There's this website www.reliable-store.com
They have books on ALL vehicles.
it covers wiring diagrams, electrical diagrams,
fuse diagram, torque specs, PCV, error codes, fault codes, service info, repair info, parts info, troubleshooting owner's/service/
repair/parts/maintenance manuals etc everything totally..
I have 1987 toyota 4runner model and I keep servicing and when needed repair it on my own. worth it !!!

2001 Oldsmobile... | Answered on Mar 18, 2018


Unfortunately you now probably have a sticking solenoid in the transmission, but you also may have an oil pump problem in the transmission. These are expensive repairs, so I would try having the transmission oil replaced and perhaps adding an additive recommended for this.

2001 Oldsmobile... | Answered on Feb 09, 2018


probably made a harness connection to the fuel pump come apart in the fitting the new transmission

2001 Oldsmobile... | Answered on Feb 07, 2018


Delphi manufactures a number of aftermarket replacement parts. If Delphi says a specific part will fit your car, you should have no problem.

2001 Oldsmobile... | Answered on Feb 05, 2018


Replace the oring and seal. I can't remember if the line swivels. If it does then there is a seal it there. If it's a solid fit. Either you have a dirty end or the line is wrong and needs the correct fitting.

2001 Oldsmobile... | Answered on Feb 01, 2018


IF the light is on, a trouble code is stored. Get the code read. There's no way to know which wheel speed sensor is bad without the code.

2001 Oldsmobile... | Answered on Jan 23, 2018


If the brakes are spongy, there is still air in the lines. Are you sure that you are using the correct technique to bleed the brakes as it is generally a very simple job to get all the air out.

2001 Oldsmobile... | Answered on Jan 03, 2018


You better get this checked out by a mechanic. This computer problem could cost a lot of money if not repaired ASAP

2001 Oldsmobile... | Answered on Dec 21, 2017

Not finding what you are looking for?
2001 Oldsmobile Alero Logo

1,868 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Oldsmobile Experts

Jonah Oneal

Level 3 Expert

14092 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Alero Oldsmobile

  • Alero Oldsmobile

Most Popular Question

2001 oldsmobile alero sputtering cutting

  • Cars & Trucks
Loading...