Help with location and replacing blower motor resistor

The blower resistor in a Toyota Townace Noah with a 3S engine is typically located near the blower motor, which is responsible for directing air into the vehicle's cabin.
Here is a general guide on how to locate the blower resistor in a Toyota Townace Noah with a 3S engine:

1. Locate the blower motor: The blower motor is typically located under the passenger side dashboard, near the footwell.
2. Identify the blower resistor: The blower resistor is typically a small rectangular or cylindrical component that is connected to the wiring harness near the blower motor.
3. Remove the blower resistor: To access the blower resistor, you may need to remove the cover or the panel that covers the blower motor. You can then unplug the wiring harness and remove the mounting bolts to remove the blower resistor.

Note: The location and accessibility of the blower resistor may vary depending on the specific model and year of your Toyota Townace Noah with a 3S engine. If you are unsure about the location or how to access the blower resistor, it is recommended to consult a professional mechanic or the vehicle's owner's manual.
It is important to handle the blower resistor with care, as it can be easily damaged if not handled properly. If you are not confident in your ability to replace the blower resistor, it is best to seek assistance from a qualified mechanic.

The heater blower motor resistor is located underneath the dashboard in the heater/AC compartment.


Heater Blower Motor Resistor Replacement - YourMechanic

https://www.yourmechanic.com/.../heater-blower-motor-resistor-replaceme...
Feedback

Replacing A Blower Motor That Doesn't Blow - YouTube

? 2:29
https://www.youtube.com/watch?v=4edK8fa-Ypg
Mar 9, 2011 - Uploaded by Scotty Kilmer
Scotty Kilmer, mechanic for the last 46 years, shows how you can replace a broken blower motor in your car ...

Blower Motor Replacement and More - YouTube

? 13:19
https://www.youtube.com/watch?v=2p5QYd58sTk
Jun 12, 2012 - Uploaded by talyn875
Do not try this at home. For HVAC professional use only. This video shows yours truly changing a blower motor ...

www.car-part.com

Its located under dash,or near glove box.

The dash panel lower side has to be out.

HEATER BLOWER MOTOR

Its faulty blower motor resistor. The low and medium speed on blower motor is controlled by resistor and its actual speed is high. So because resistor is not working, blower motors actual speed which is high is working.

It can be faulty blower motor or faulty blower motor resistor. Get the blower motor inspected. If it's faulty it has to be replaced.

=======

For blower motor testing and replacing, check the link below: ----

Blower motor Testing/replacing for all vehicles?

http://repairhelpcenter.blogspot.in/2012/02/blower-motor-replacing-for-all-vehicles.html

------------

These will help.

Thanks.

Yes both relay and switch are possible.Needs to be inspected.
Blower motor replacing for all vehicles? http://repairhelpcenter.blogspot.in/2012/02/blower-motor-replacing-for-all-vehicles.html

Blower motor Resistor shorting problem?

http://schematicsdiagram.blogspot.com/2011/12/blower-motor-resistor-shorting-problem.html

How to remove Blower control switch? http://howtobyme.blogspot.in/2012/02/how-to-remove-blower-control-switch-on.html

---------

Where is blower motor relay located ? http://technoanswers.blogspot.in/2012/02/where-is-blower-motor-relay-located-on.html

--------

This will help.Thanks.

This problem is caused by a defective blower motor speed control resistor.

BLOWER MOTOR LOCATION
The blower motor resistor is located under the glove box. You can locate it by finding a 4 wire connector, directly below the glove box hinge (towards the front of the truck). There are 2 screws holding it in. A mirror is helpful in replacing this, but I managed to replace it without one. You will need a nut driver to remove the screws. My suggestion is to leave the wires connected to the resistor while removing the screws.

The Blower Motor Resistor Block is usually located in the air duct on the output side of the blower motor. It is placed here so that air flow from the fan helps stop the resistiors from overheating and burning out. It should be obvious once you look near to where you replaced the blower motor.

First locate blower motor. The resistor is in the duct that the blower motor blows through. The resistor is actually cooled off by the blower motor. Usually it is within a foot of the blower motor & is accesible the same way that the blower motor is mounted. It may help for you to see the replacement part. All you will see next to motor is the end the wire plugs into & how it screws into duct.

Dear Blower Motor Searcher,
The blower motor is located under the dash on the pass side in front.Open the pass front door , get on your knees, and look up under the dash, you will see the flying saucer looking object, that is the blower motor.Right next to it is where the resistor is located, and yes it is recomended that you replace the resistor also because that is where the main current flows thru to get to the blower motor.That actually controls the current of the motor, which controls the speed of the motor, low, med, high, recirc, etc....any other questions get back to me, TX!! HOPE I COULD HELP!!!

If it only works on high, replace blower motor resistor.