95 f250 7.3 is throttle position sensor on the pedal

no TATA in USA ,
no year told no engine size diesel told
did not scan the PCm or DTC error the CEL lamp on, begging you to do.
find a forum in India
and win.\
\do put in new fuel filters it is a #1 top service that cannot be ignored.

the limphome mode has many causes
GUE$$ing will be super expensive. seems it is already.

google why is my check engine lamp on
read.
100rds of ways and millions of posts world wide
learn to check all fuses,
scan the pcm
and the fuel filter can not be ignored on Diesels.

Your engine has an electronic throttle body. They don't use an idle air control valve. They control idle by cracking open the throttle plate electronically. If you have idle problems, chances are you've got carbon buildup around the throttle plate. Here's how to clean it. http://ricksfreeautorepairadvice.com/clean-an-electronic-throttle-body

Reduced Engine Power Mode When the ECM detects a condition with the TAC system, the ECM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
?€¢
Acceleration limiting--The ECM will continue to use the accelerator pedal for throttle control, however, the vehicle acceleration is limited.

?€¢
Limited throttle mode--The ECM will continue to use the accelerator pedal for throttle control, however, the maximum throttle opening is limited.

?€¢
Throttle default mode--The ECM will turn OFF the throttle actuator motor and the throttle will return to the spring loaded default position.

?€¢
Forced idle mode--The ECM will perform the following actions:

-
Limit engine speed to idle by positioning the throttle position, or by controlling the fuel and spark if the throttle is turned OFF

-
Ignore the accelerator pedal input

?€¢
Engine shutdown mode--The ECM will disable fuel and de-energize the throttle actuator.
Did you have it checked for DTC's - diagnostic trouble code's related to the reduced engine power ?
All so has APP sensor gas pedal !
Accelerator Pedal Position (APP) Sensor
The accelerator pedal contains 2 individual accelerator pedal position (APP) sensors within the assembly. The APP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
?€¢
A 5-volt reference circuit

?€¢
A low reference circuit

?€¢
A signal circuit

The APP sensors are used to determine the pedal angle. The engine control module (ECM) provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors provide the ECM with signal voltage proportional to the pedal movement. The APP sensor 1 signal voltage at rest position is less than 1 volt and increases to more than 4 volts as the pedal is actuated. The APP sensor 2 signal voltage at rest position is less than 0.6 volt and increases to more than 2 volts as the pedal is actuated.
Your best bet is take your vehicle to the dealer !
al

Your Denali has Throttle Actuator Control (TAC) System - Electronic throttle control ! Are there any messages on the driver information center ? Reduced engine power ?
Reduced Engine Power Mode When the PCM detects a condition with the TAC system the PCM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
?€¢
Acceleration limiting--The control module will continue to use the accelerator pedal for throttle control; however, the vehicle acceleration is limited.

?€¢
Limited throttle mode--The control module will continue to use the accelerator pedal for throttle control; however, the maximum throttle opening is limited.

?€¢
Throttle default mode--The control module will turn off the throttle actuator motor and the throttle will return to the spring loaded default position.

?€¢
Forced idle mode--The control module will perform the following actions:

-
Limit engine speed to idle by positioning throttle position, or by controlling fuel and spark if throttle is turned off.

-
Ignore accelerator pedal input.

?€¢
Engine shutdown mode--The control module will disable fuel and de-energize the throttle actuator.

You need to have it checked for DTC'S - diagnostic trouble codes , probably a accelerator pedal position (APP) sensor or TPS - throttle position sensor !

Error Code: P0221
Description:
Throttle Position (TP) Switch/Sensor B
Accelerator Pedal Position (APP) Switch/Sensor B Range/Performance Problem
Possible Cause:
- Accelerator cable adjustment.
- Throttle position (TP) switch/sensor .
- Accelerator pedal position (APP) switch/sensor.
- Check valve clearance, adjust if required.

No messaage of reduced engine power ? Your vehicle has electronic throttle control . Has four position sensors , two are located in the gas pedal ,an two in the throttle body . The PCM uses these sensor to know how much to open the throttle plate ,allowing more air into the engine . How did you read this code an where did you read it's definition at ? This is not a code for your vehicle . Some time cheap code readers get them wrong .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit
DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage
DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit
DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

DTC P1516: Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance
DTC P2101: Throttle Actuator Position Performance
DTC P2119: Throttle Closed Position Performance
DTC P2176: Minimum Throttle Position Not Learned

If one of this position sensors is bad it will throw the PCM into a
Reduced Engine Power Mode
When the ECM detects a condition with the TAC system, the ECM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
• Acceleration limiting--The ECM will continue to use the accelerator pedal for throttle control; however, the vehicle acceleration is limited.
• Limited throttle mode--The ECM will continue to use the accelerator pedal for throttle control; however, the maximum throttle opening is limited.
• Throttle default mode--The ECM will turn off the throttle actuator motor and the throttle will return to the spring loaded default position.
• Forced idle mode--The ECM will perform the following actions:
- Limit engine speed to idle by positioning the throttle position, or by controlling the fuel and spark if the throttle is turned off.
- Ignore the accelerator pedal input.
• Engine shutdown mode--The ECM will disable fuel and de-energize the throttle actuator.


017 Accelerator Pedal Position Sensors
Drive by Wire Function and diagnostics by Wells

REDUCED POWER
Refer to:
• Powertrain Control Module Description for the 2.8L engine
• Powertrain Control Module Description for the 3.5L engine

Throttle Actuator Control (TAC) System
Throttle Actuator Control (TAC) Overview
The throttle actuator control (TAC) system uses vehicle electronics and components to calculate and control the position of the throttle blade. This eliminates the need for a mechanical cable attachment from the accelerator pedal to the throttle body. This system also performs the cruise control functions as well.
The TAC system components include, but are not limited to the following:
• The accelerator pedal position (APP) sensors
• The throttle body
• The powertrain control module (PCM)
Each of these components interface together to ensure accurate calculations and control of the throttle position.

Accelerator Pedal Position (APP) Sensor
The accelerator pedal position (APP) sensor is mounted on the accelerator pedal assembly. The APP is 2 individual APP sensors within one housing. There are 2 separate signal, low reference, and 5-volt reference circuits. APP sensor 1 voltage increases as the accelerator pedal is depressed. APP sensor 2 voltage decreases as the accelerator pedal is depressed.
Throttle Body Assembly
The throttle body for the throttle actuator control (TAC) system is similar to a conventional throttle body with several exceptions. One exception being the use of a motor to control the throttle position instead of a mechanical cable. Another exception is the throttle position (TP) sensor. The TP sensor is mounted in the throttle body assembly. The TP sensor is 2 individual TP sensors within the throttle body assembly. Two separate signals, low reference, and 5-volt reference circuits are used to connect the TP sensors and the powertrain control module (PCM). TP sensor 2 signal voltage increases as the throttle opens. TP sensor 1 signal voltage decreases as the throttle opens.

Reduced Engine Power Mode
When the PCM detects a problem with the throttle actuator control (TAC) system the PCM enters one of the following Reduced Engine Power Modes:
• Acceleration Limiting--The control module will continue to use the accelerator pedal for throttle control, however the vehicle acceleration is limited.
• Limited Throttle Mode--The control module will continue to use the accelerator pedal for throttle control, however the maximum throttle opening is limited.
• Throttle Default Mode--The control module will turn OFF the throttle actuator.
• Forced Idle Mode--The control module will perform the following actions:
- Limit engine speed to idle by positioning throttle position, or by controlling fuel and spark if throttle is turned OFF.
- Ignore accelerator pedal input.
• Engine Shutdown Mode--The control module will disable fuel and de-energize the throttle actuator.

Have you had it checked for DTC'S - diagnostic trouble codes ?

DTC P2176
The commanded throttle position (TP) is compared to the actual TP. Both values should be within a calibrated range of each other. The powertrain control module (PCM) continuously monitors the commanded and actual TPs. If the values are greater than the calibrated range, DTC P2176 sets.
--------------------------------------------------------------------------------
DTC P2138
The accelerator pedal position (APP) sensors 1 and 2 are located within the accelerator pedal assembly. Each sensor has the following circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
This provides the powertrain control module (PCM) with a signal voltage proportional to accelerator pedal movement. The APP sensor 1 signal voltage at rest position is near the low reference and increases as the pedal is actuated. The APP sensor 2 signal voltage at rest position is near the 5-volt reference and decreases as the pedal is actuated.
DTC P2135
The throttle actuator control (TAC) assembly has 2 throttle position (TP) sensors mounted within the assembly. The powertrain control module (PCM) provides individual signal, ground, and 5-volt reference circuits to each sensor. Both sensors operate within a voltage range between 0.35-4.65 volts. When the throttle is opened from 0-100 percent, one sensor signal voltage increases while the other decreases. The signal circuit for TP sensor 1 is referenced to ground, and the signal circuit for TP sensor 2 is pulled up to 5 volts within the PCM.
DTC P2128
DTC P2127
DTC P2125
DTC P2123

Drive by Wire Function and diagnostics by Wells

Is the check engine light on ?
I am assuming this is a full size Dodge truck and that is has a throttle position sensor.
If the fuel pressure is within spec, the throttle position sensor may be faulty or you could have a problem with the throttle cable.

fords/international have pad pedal position/throttle position sensors that go bad and you can replace the sensor or the entire pedal but does anyone know what the other sensor is underneath the tps. an accelerator switch??

I have also read in the service manual that doing an idle relearn helps with RPM problems. This is the procedure below. It is complicated to do unless you have a watch or something to count the seconds with.

DESCRIPTION
“Accelerator Pedal Released Position Learning” is an operation to learn the fully released position of the accelerator
pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time
harness connector of accelerator pedal position sensor or ECM is disconnected.
OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch “ON” and wait at least 2 seconds.
3. Turn ignition switch “OFF” wait at least 10 seconds.
4. Turn ignition switch “ON” and wait at least 2 seconds.
5. Turn ignition switch “OFF” wait at least 10 seconds.
Throttle Valve Closed Position Learning UBS002OA
DESCRIPTION
“Throttle Valve Closed Position Learning” is an operation to learn the fully closed position of the throttle valve
by monitoring the throttle position sensor output signal. It must be performed each time harness connector of
electric throttle control actuator or ECM is disconnected.
OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch “ON”.
3. Turn ignition switch “OFF” wait at least 10 seconds.
Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.
Idle Air Volume Learning UBS002OB
DESCRIPTION
“Idle Air Volume Learning” is an operation to learn the idle air volume that keeps each engine within the specific
range. It must be performed under any of the following conditions:

Each time electric throttle control actuator or ECM is replaced.

Idle speed or ignition timing is out of specification.
PREPARATION
Before performing “Idle Air Volume Learning”, make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.

Battery voltage: More than 12.9V (At idle)

Engine coolant temperature: 70 - 95ｰC (158 - 203ｰF)

PNP switch: ON

Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
On vehicles equipped with daytime light systems, set lighting switch to the 1st position to light
only small lamps.

Steering wheel: Neutral (Straight-ahead position)

Vehicle speed: Stopped