Razor Toys - Page 3 - Popular Questions, Answers, Tips & Manuals
E300
Im not sure I understand your question. The E300 runs on 2 batteries at a time and they recharge in the unit. To replace them clnnect one + to the other - and the remaining + and - to the unit.
9/8/2014 12:17:07 PM •
Razor E300...
•
135 views • 0 helpful votes
ON/OFF SWITCH BROKEN ON SCOOTER E100
Replace the Red Illuminated Light On/Off SPST Rocker Switch 15A/250V 30A/125 - Switch number SWT-102050 should be available
at most scooter repair stores or online scooter repair for about $6.00.
Black wire goes to the Brass terminal lug. when removing the wires mark the location as Top, Center and Bottom and place the Black wire on top with the brass terminal.
to Search Online Type 'scooter repair SWT-102050' you will see a multitude of choices
6/30/2014 1:03:50 PM •
Razor E100...
•
880 views • 0 helpful votes
Need schematic diagram
google it and browse the image section for best chance without you contacting the manuf.
8/11/2014 11:55:22 PM •
Razor E300...
•
96 views • 0 helpful votes
No power
Could be the battery.
Put the Scooter on a block so the rear tire is raised. Remove the standing plate to reveal the battery compartment.
Charge the Unit completely
1. Using a multimeter measure the voltage across the batteries. If the voltage is below 20 volts batteries are dead - Replace batteries.
2. Now for a running test. Turn the throttle and spin the rear tire to preform a kick start. Still measuring the voltage. If the voltage is Below 20 volts or if the voltage drops quickly batteries are dead - Replace batteries.
3. If the voltage is remaining around 24 volts for a long period - then you could have connector problems, clean and tighten all connectors.
I use a fiberglass electronic cleaning brush, as contact cleaners leave residue that interfere with electrical connections.
The control module is simple and can be replaced with only a 24 volt relay without the kick start feature or Brake. If you want the brake then you can use two 24 volt relays still no Kick Start.
For those of you who know electrical, below is circuits I developed to replace the controller. This diagram will also give you a better understanding on the Razor circuit.
NOTE : This is not a schematic diagram of the Razor E100 Control Module. I designed this circuit. for my Great Nephew's Scooter.
1. The Brake is a normally closed switch that opens when you squeeze the Brake handle.
2. The throttle is two normally open switches that close when you turn the throttle.
3. The Kick Start circuit is described in the Diagram below.
4. The resistors values may need to be tweaked for best performance.
4/21/2014 10:45:05 AM •
Razor E100...
•
335 views • 1 helpful votes
E300 electric scooter battery,
The scooter uses batteries specifically designed for deep discharge applications. If your new batteries are not lasting then they may only be suitable for standby or backup type applications like for your house alarm system or garage door opener when the mains power goes out.
3/19/2014 9:41:42 PM •
Razor E300...
•
673 views • 0 helpful votes
ALSO IF ANYONE HAS ANY TROUBLE WITH RAZOR SCOOTERS WITH GETTING THEM TO GO,IT CAN BE THE TENSIONER,WHEELS,CHAIN,MOTOR,BATTERY,CHARGER,CONTROL MODULE,RESET BUTTON,LIGHT SWITCH,AND THROTTLE.IF IT WORKS,
I purchased my batteries on E-bay. Selected the highest rated with a Square trader warranty. Delivery time was 4 days, new was was going to ask.
Delivered to my house for$21.00 with both batteries, charged and ran perfectly. Extended Warranty was also offered but declined.
Batteries still working great 6-months latter.
3/8/2014 9:39:06 PM •
Razor E300...
•
696 views • 1 helpful votes
Battery razor e 100 replace
Could be the battery.
Put the Scooter on a block so the rear tire is raised. Remove the standing plate to reveal the battery compartment.
Charge the Unit completely
1. Using a multimeter measure the voltage across the batteries. If the voltage is below 20 volts batteries are dead - Replace batteries.
2. Now for a running test. Turn the throttle and spin the rear tire to preform a kick start. Still measuring the voltage. If the voltage is Below 20 volts or if the voltage drops quickly batteries are dead - Replace batteries.
3. If the voltage is remaining around 24 volts for a long period - then you could have connector problems, clean and tighten all connectors.
I use a fiberglass electronic cleaning brush, as contact cleaners leave residue that interfere with electrical connections.
The control module is simple and can be replaced with only a 24 volt relay without the kick start feature or Brake. If you want the brake then you can use two 24 volt relays still no Kick Start.
For those of you who know electrical, below is circuits I developed to replace the controller. This diagram will also give you a better understanding on the Razor circuit.
NOTE : This is not a schematic diagram of the Razor E100 Control Module. I designed this circuit. for my Great Nephew's Scooter.
1. The Brake is a normally closed switch that opens when you squeeze the Brake handle.
2. The throttle is two normally open switches that close when you turn the throttle.
3. The Kick Start circuit is described in the Diagram below.
4. The resistors values may need to be tweaked for best performance.
4/12/2014 1:44:21 PM •
Razor E100...
•
248 views • 0 helpful votes
Battery problems
You might still be under warranty. If so follow the instructions on the box.
If you do not have a warranty, try a different outlet in your house. If this doesn't work, look up your model number and then battery on
eBay and
Amazon.
Hope this Helps You, if it does be safe.
5/4/2014 5:34:21 PM •
Razor E100...
•
122 views • 0 helpful votes
How i can pump the weels on the back
Hi, you need to take the end-cap off of the right side of the handle bar. It is a black cap/plug that pulls out. You will see a black plastic piece that's about 3" long. Pull that out of the end cap. This is the extension that is screwed on the the air valve. Just place through the hole in the rear sprocket and thread on, and fill the tire with air. When done, unthread it and replace back into handle-bar end-cap and reinstall the end-cap. It only took me 4years to figure that out!
Wont work
check the battery that is most likely what's wrong
4/15/2014 10:14:30 PM •
Razor E100...
•
64 views • 0 helpful votes
Not finding what you are looking for?