Kenwood Food Mixers - Answered Questions & Fixed Issues


Contact Kenwood directly to order.

Kenwood Food... | Answered on Sep 09, 2019 | 462 views


there is one here...
http://web.archive.org/web/200707171...tions-A701.pdfbut the pages are in the wrong order and i think some are missing.

Kenwood Food... | Answered on Sep 07, 2019 | 10,910 views


There is a Triac that controls the speed. It is probably short circuit. A qualified Electronics engineer with mechanical skills can repair it. Probably a BT139-600.

Kenwood Food... | Answered on May 18, 2019 | 76 views


KMX50 would start and accelerate to high speed, then slow down some with fairly erratic speed. I tried changing the triac on the main speed control board, then also the whole board (£45). It made no difference.

The only other component I realised it might be was the speed control board which is on the rear end of the motor under the main cover (I found this component on a site selling Kenwood parts, and was where I got the main board from, which is how I know it's speed control). When I inspected it I found two of the terminals broken. You had to look very closely to see they were broken. It's a poor design as the three legs of the terminals are quite long, and very thin, so on high speed when kneading there is much vibration, which is why I suspect the terminals broke. I cut them back just enough to resolder. The component isn't quite fully inside the sensor wheel on the motor shaft, but it still picks up sufficient signal to control the speed and now works fine. Haven't tried it under load yet, but no reason to think it won't work correctly. So check this before ordering a £45 board!

Kenwood Kmix... | Answered on May 16, 2019 | 348 views


Need to take a 2x4 balance it between the outlet for the grass and maybe a pair of vise scrips and then try to take it off.

Kenwood Food... | Answered on Mar 31, 2019 | 79 views


Sounds as if the amplifier is overheating? Does it do this at all volume levels or only when turned up to higher levels- if so it's likely the amplifier inside of the receiver.
ac096182-5c40-4da4-aee7-2a0ee52a59a0-nuhf2ssaswwsu1mfl2kxuue2-5-0.jpeg

Kenwood Food... | Answered on Mar 17, 2019 | 78 views


are you smart enough to try ???

Kenwood Food... | Answered on Feb 26, 2019 | 73 views


Any idea how many operational hours? I suspect motor brushes but can be other.

Kenwood Food... | Answered on Jan 23, 2019 | 102 views


DNO IT CAN NOT BLENDERS OR FOOD PEOCESSERS WILL NOT HAND MIXERS

Kenwood Food... | Answered on Jan 22, 2019 | 99 views


If you do not know what you are doing it is better to throw it away and get a new one. You could get electrocuted if you try yourself. Probably cost more than a new one to get someone to repair it.

Kenwood Food... | Answered on Nov 13, 2018 | 208 views


The speed switch may be defective.

Kenwood Food... | Answered on Sep 28, 2018 | 179 views


Not sure how to change the switch but some knobs are retained by a small grub-screw or a spring clip and it is sometimes worthwhile checking the switch shaft is actually being turned by the knob.

Kenwood Food... | Answered on Sep 24, 2018 | 234 views

Not finding what you are looking for?
Kenwood Logo

Ask a Question

Usually answered in minutes!

Top Kenwood Food Mixers Experts

Peter GW Fleming

Level 1 Expert

3 Answers

Treefrog15
Treefrog15

Level 2 Expert

130 Answers

Yitz Diss

Level 1 Expert

9 Answers

Are you a Kenwood Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...