Kenwood Logo

Kenwood Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 2K Products
  • 75K Answers
  • 2M Views

make sure you have no bare or shorted speaker wires and check your speakers to make sure they are all good. if that all checks out, you probably have a bad output ic.

Kenwood... | Answered 10 hours ago


if you have bypass button in your equalizer check if not depressed.

Kenwood KE-205... | Answered Yesterday


Yoou deselect key in programming. OR you press key one by one and when you see key sign dis appear,it mean your channel is unlock know.

Kenwood Radio... | Answered Yesterday


make sure that both have a same frequency and same DQT of both radios ot at DQT select None. Then will see radios will works perfectly.

Kenwood Radio... | Answered Yesterday


What button should I push if I don't have an "auto" button, both on the remote or the head unit? I have a dNx-5140. All help would be appreciated.

Kenwood... | Answered Yesterday


YOU SHOUL CHECK YOU BATTERY AND GROUND AND REMOTE SOURCE MAKE SURE THEY ARE CONNECT PROPERLY

Kenwood Car... | Answered on Feb 19, 2019


USUALLY THERE IS NO CODE BUT IF U PURCHASE USE YOU HAVE GET CODE

OR TURN KEY AND PUSH RESET BUTTON FOR TEN SECOND THEN TURN OFF AND TRY TURN ON

Kenwood Car... | Answered on Feb 19, 2019


YELLOW- BATTERY +
BLK -GROUND
RED- ACCESSORY
BLUE- ANTENNA
BLUE/WHITE-AMP TURN ON
BLUE/YELLOW STREERING REMOTE

SPEAKER WIRIES;;;
WHITE +
WHITE/BLK --] LEFT FRONT

GRAY+
GRAY/BLK--} RIGHT FRONT

GREEN+
GREEN/BLK--} RIGHT LEFT REAR

PURPLE+
PURPLE/BLK--} RIGHT REAR

Kenwood Car... | Answered on Feb 19, 2019


VIDEO CARD READER OF UNIT IS BAD YOU HAVE TO FIND A TECH SUPPORT WITH KENWOOD TO FIX

Kenwood Car... | Answered on Feb 19, 2019


UNPLUNG THE UNIT WAIT TEN SECOND THE PLUG BACK IN

Kenwood Car... | Answered on Feb 19, 2019


I couldn't remove the K-Beater as when I tried to turn it the whole mechanism turned with it. I couldn't even remove the splashguard! I was going to take it to the Kenwood factory (a few miles from home) but then I thought I'd give it one more go and this is what I did...
  1. Next to where the K-Beater attaches in the middle of the circular plate is a lug with a pointed-shape bolt on the end. Remove this with a spanner and the beater plus gear cog can be removed.
  2. Place some mole grips or wide pliers on a worktop and sit the cogged gear in to it and grip so that it won't turn.
  3. Now you should be able to remove the K-Beater!
Perhaps someone can suggest how to stop it happening again. I haven't attached anything since but will update this post if I have any other helpful tips.

Kenwood KM400 /... | Answered on Feb 18, 2019


That error is normally a shorted speaker wire but starting the car won't cause that. Possible problem could be the dimmer wire was used as a ground by mistake. Lights come on when the car starts. Another is too high of voltage. Car rests at 12 volts but is around 14 when running. Was there a plastic piece on the red or yellow wire that got cut off during the install? They have a resistor inside that keeps the voltage down.

Kenwood Car... | Answered on Feb 17, 2019


Contact service engineer, it may require to replace it's carbon brushes

Kenwood Food... | Answered on Feb 15, 2019


Contact Kenwood directly and request the wiring diagram.

Kenwood Car... | Answered on Feb 13, 2019


Going in the clock menu setting and follow the steps to set clock

Kenwood Car... | Answered on Feb 12, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Kenwood Experts

Marvin
Marvin

Level 3 Expert

83959 Answers

The Knight
The Knight

Level 3 Expert

76016 Answers

Brad Brown

Level 3 Expert

17979 Answers

Are you a Kenwood Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...