JVC Popular Questions, Answers, Tips & Manuals

To reset the clock on a JVC PC-110 boombox from 1994, follow these steps:

1. Press the Clock Set button, located on the top of the boombox, to enter clock setting mode.
2. Press and hold the Clock Set button until the hour digits on the display start flashing.
3. Use the Fast Forward and Rewind buttons to adjust the hour to the correct time.
4. Press the Clock Set button again to move to the minute digits. The minute digits will start flashing.
5. Use the Fast Forward and Rewind buttons to adjust the minute to the correct time.
6. Press the Clock Set button one final time to exit clock setting mode and save the new time.

Your JVC PC-110 boombox should now display the correct time.

Strangely, that information is not available anywhere. Contact JVC direct. Lots of mentions, but no wiring. https://www.google.com/search?q=jvc+kd-sr61+wiring+diagram ..

Check each set of wires and speakers to be sure no wire or lead is connected to a chassis ground. The radio will see this as a short and turn off the internal amplifier causing the on but no sound issue. Each speaker connected to the radio needs dedicated positive and negative leads from the radio to each speaker. HOPE THIS HELP!

Unless you have electronic schooling and the equipment don't attempt to fix it yourself, it's a guessing game as far as what board, backlights or panel is causing the issue unless you have equipment, knowledge and service manual recycle it.

The blinking red light on your JVC projection TV could indicate a problem with the TV's power supply, lamp, or other internal component. Here are some steps you can take to try to resolve the issue:

1. Check the power cord: Make sure the power cord is plugged in securely to the TV and the power outlet. If the cord is loose or damaged, the TV may not receive the power it needs to turn on.
2. Reset the TV: Unplug the TV from the power outlet and wait a few minutes before plugging it back in. This may reset the TV's internal system and resolve the issue.
3. Replace the lamp: If the TV has been used for a long time, the lamp may be burnt out and need to be replaced. Check the owner's manual or contact JVC customer support for instructions on how to replace the lamp.
4. Contact customer support: If none of the above steps work, the TV may have a more serious problem that requires professional repair. Contact JVC customer support for assistance or to find an authorized repair center in your area.

Bearing in mind that this equipment coexisted with Windows XP, you can try emailing jvc suppport requesting the driver or venture into the quicksand pit of driver updaters. There you may or may not find a compatible driver, bearing in mind some updaters will claim to have a compatilbe driver up to and including Windows 11. Some forums suggest you don't need a special driver. other forum users say they have tried various drivers and not found them to work. And then there are those who claim the driver came out on CD. Would that leave you looking for an XP computer to run the driver upon? you would be chasing air to find a very recent laptop having a CD reader. I make no claim to knowing whether the following would work for you, given the original driver was XP compatible. i would make a restore point before even trying it; https://www.solvusoft.com/en/update/drivers/digital-video-recorder/jvc/gr-dx37/sub-models/ https://www.driverguide.com/driver/detail.php?driverid=1404220 https://forums.techarp.com/threads/jvc-gr-dx37-camcorder-driver.17415/ https://www.jvc.com/usa/support/

Hi, This comes on if you might have a short somewhere in your system. Please check all of the wires for any type of damage and make sure they're connected as intended by the manufacturer (can verify in your manual). Thank you.

No, the Empress is a single appliance remote not universal. Have a read https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote ..

Hi, those buttons should be on the front of the boom box. But if you can't find them, please check the back of the boom box. Otherwise, you'll need to use page 24 of the manual to help identify the buttons. Thank you.

Here are some troubleshooting steps you can try to fix the sound issue on your JVC TV:

1. Check the volume level: Make sure that the TV volume is not muted and the volume level is high enough to be audible.
2. Check the connections: Ensure that the audio cables are properly connected to the TV and the external speakers. If you're using an external audio device, check its connections as well.
3. Try resetting the TV: Turn off the TV and unplug it from the power source for a few minutes. Then plug it back in and turn it on.
4. Check the audio settings: Access the TV's audio settings menu and ensure that the sound mode is set to "Stereo" or "Mono". You can also try changing the audio output settings to "TV Speakers" or "External Speakers" depending on what you're using.
5. Try using a different audio device: If the above steps don't work, try connecting a different audio device to the TV to see if the sound works. This will help you determine if the problem is with the TV or the audio device.

If none of these steps work, it's possible that there may be an issue with the TV's audio hardware, and you may need to contact a professional repair service or the manufacturer for further assistance.

Try doing a Factory Reset on it. https://www.google.com/search?q=JVC+TV+is+stuck+in+stereo+mode ..

Hi, if you've used the service manual and problem still exists, then might need to have the backlight replaced by jvc directly. You can reach out to them by calling 1 (800) 252-5722. Thank you.

Question edited for clarity. That wasn't a 'serial number', it is the model number. What sort of 'code', universal remote code? Read this https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote ..

Hi, scm might stand for skip-continuously-mode where songs play in no particular order. To be sure, we would need to look at the list of modes in your device's manual. These are where all acronyms are usually explained. Thank you.

bad power supply

take the PDF to any town copy centers the will print it for you or buy your own printer or as a buddy to barrow one. this post is how to print a PDF google that see 100million answers, all correct. for 4 decades now.

Aux is not a headphone output, it is for another amplifier.

I need to know how the DVD player is hooked up in the back. Are you using HDMI, component or composite cables?

From memory, no pun intended, there is a large value capacitor or a battery type BN-V416 that holds the memory settings. A service engineer should be able to help.

JVC Plasma Television?? It seems to be a very rare model because Google doesn't know it. Take it to your neared Google Service Centre. https://www.google.com/search?q=JVC+PD-51NO3B ..