JVC Logo

JVC Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 4K Products
  • 97K Answers
  • 3M Views

Turn off the timer in menu set
4_23_2019_5_53_09_pm.jpg

JVC Televison &... | Answered Yesterday


Unlike some apps which require sideloading, you can install Chrome on your Android TV device using a web browser on another machine:
  1. On the computer, navigate to Google Play.
  2. Click on Apps in the left-hand panel.
  3. Type Chrome in the search box and press Enter.
  4. Open the app listing.
  5. Click on Install.
  6. Choose your Android TV device from the dropdown menu.
  7. Click Install.

JVC Televison &... | Answered Yesterday


I have a JVC DLA-X9-B projector which I think is the almost the same as the X7 and X3 the manual is the same.Its about 2 years old.It stopped working suddenly while I was watching a movie. Indicator lights were both on red and lamp light flashing orange. Replaced the lamp and it did not change the status,did cleaning filter bit , did lamp reset from the remote , did reboot and plugged it at a different ac outlet all that did not work . The lens cover is stuck at opened and the only thing you get when plugged in is the red light on and after 30 seconds the lamp light comes on orange .No fan came on no moving lens cover only flashing orange light.
From this conclusion was the power supply was working and software was a question mark either it was corrupt ,but the power cycle and lamp test start was normal and it checked the lamp and reported orange .So all the more it pointed to either the ballast or the power feeding the ballast.
I opened the projector up started with the screws at the bottom removed the the adjustable screw in legs. Removed the left and the right plastic cover ,then bottom cover, lamp cover, top cover plastic and then top metal plate cover, back cover until parts were all visible ,then put back the screw in legs a placed projector in an upright position. All this was in suspect that the ballast is the problem.
jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-6.jpgThis is the top view photo.
On the right black plastic cover is the lamp fan and air duct.
At the center is the lens assembly and motors for focus lens shift etc.
on the left are stacks of electronics that are stacked board on board of about 4 or 5 layers.

jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-11.jpgthis is the side view of the stacks of boards, to get to the ballast these have to be removed.NOTE LABLE ALL CABLES AFTER REMOVING THEM AS THERE ARE MANY OF THEM.Remove the side plate

jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-18.jpg
Remove hdmi and land board,carefully there are connectors on bottom and all sides of this board.

jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-27.jpg jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-38.jpgthen remove the next board ,remember to lable all the cables.
jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-51.jpgthen the next board bellow ,carefull this one has 2 side connectors on pictures top side
jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-66.jpgthis will be what it looks like.Note the bottom most is the power supply.,This feeds the ballast as well as other low voltage Dc components.THE CONNECTOR WITH THE WHITE END AND BLACK AND RED CABELS IS THE BALLAST FEED(picture above) .The ballast is located in a black plastic box above the power supply.The only way to remove it is to continue dismantling further. jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-83.jpgthis is the top view and the yellow tags you are seeing is cable labelson the wires.

jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-102.jpgthis picture is with all boards removed to check for physical burn outs on components
mainly on power supply ballast feed and ballast itself.
jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-123.jpgall boards out
jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-146.jpgthis is the power supply board it has both low and high voltage output .Low for logic boards high output for ballast.Ballast feed from power supply should put out about 380 volts dc during projector boot up and zero during orange blinking light,(you can skip this removal of power supply if you read the 380 volts output on multimeter at boot up.Do this before taking all the boards apart but remove the side plate to access the output and check the output at boot up ,warning do not short this while reading output.
jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-171.jpgpower board made by sumida and so is the ballast
jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-198.jpgfinally the ballast is out this is what it looks like,do you see the dark grey wires they lead to the optocouplers (little led light sensing switch looks like a square little box all 3 are side by side)
jvc-dla-x3-bu-will-not-power-2-lights-zogl1yh0b34d0jvl0ocjipaz-3-227.jpg this resistor came out of the ballast ,notice physical damage like a hole in the center of it,tested it out of the board and yes its dead replaced this.
.Did all the checking one by one of the components then found one of the optocouplers had gone dead.The one located in the center of the 3 replaced that ,put it all back and got it working again.
The ballast cost 300 usd I bought one too and kept it handy just incase.
But for the meanwhile the old one is back and working just fine.

JVC DLA-X3... | Answered 2 days ago


remove the power to the TV (so unplug it from the power socket).
Then on the actual TV, hold the power button for 60 seconds then release.
Then wait 10 minutes, connect the power again to the TV, turn it on and tell me please if it is now operating correctly.

JVC Televison &... | Answered 2 days ago


Sorry, no. You must have the JVC MX-DK1 Upgrade disc to be able to upgrade.

JVC Audio... | Answered 3 days ago


If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Unlock procedure and to override the password lock to many popular brand TVs are given. To get more details, refer its user manual.

JVC Televison &... | Answered on Apr 20, 2019


look for a little pin hole, and push a straightened paperclip into it
cd eject hole-m5ba3hfnrm24eud1bhsx4rhg-2-0.jpg

JVC Car Audio &... | Answered on Apr 20, 2019


Hi get in touch with cruthfield
1-844-252-2966 for info on a kit to adapt it it to you're car....this wiring set up might help ..cheers
img_20190413_204346-ptr2lfgnw5x5mfqvcyj3lgu2-2-0.jpg

JVC Car Audio &... | Answered on Apr 13, 2019


There's a remote on eBay right now for $15 ~ buy it!


https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F223181164700

Hope this helps!
4_9_2019_11_48_43_pm.jpeg

JVC Televison &... | Answered on Apr 09, 2019


There are two reasons normally that the cassette door won't open when you slide the Eject button on the JVC GR-SXM320. One: the camera uses a powered eject feature. If the battery is low and the AC adapter isn't plugged in and powering the camera, this doesn't work. Two: if the LCD monitor screen is not open to more than a 60 degree angle, then there is an interlock that keeps the cassette door closed. This avoids the door hitting the screen. It's best to have the monitor at a 90 degree angle to the camera body when you open the cassette. Press Stop if there is a chance that the camera is recording to the current cassette.

JVC has the manual here: http://resources.jvc.com/Resources/00/00/97/LYT0465-001A.pdf .

Note: since the camera is older, check that the AC adapter is getting warm when it's plugged in and connected to the camera. This checks if the adapter is working. Check if your battery pack is good. If you have the BN-V856U battery pack, you need the AA-V80U charger to charge the battery. The charger that came with the camera will not work.

Third party battery packs and chargers are still available for the GR-SXM320. Use the manual to look up the part number and Google for the battery or use the camera model number to find available parts. For example, a replacement BN-V11U battery is available at Amazon and here: https://www.bestbatt.com/JVC-BN-V11U-BN-V12U-BN-V14U-BNV-V18U-Battery-p/bbbnv11u.htm .

I hope this helps.

Cindy Wells

JVC Video... | Answered on Apr 08, 2019


USE PEEL REMOTE ON A SMARTPHONE.
ONCE WORKING YOU CAN COPY TO A UNIVERSAL PROGRAMMABLE REMOTE.
QED.

JVC Audio... | Answered on Apr 07, 2019


Thank you, everyone! I thought maybe I was losing my mind. I can hardly watch a lot of the TV shows anymore due to the inappropriate use of music -- either it's too loud or there's just too darned much of it. Come on, TV producers! You are supposed to get better with time, not worse! Thank goodness I'm not alone.

JVC AV-32260 32"... | Answered on Apr 07, 2019


Use code search on the URC to find something that works. If a search through all codes stored in the URC fails, try a different one.

JVC Televison &... | Answered on Apr 06, 2019


Hi
This problem is in the screen.
The flats cables on the screen have a bad contact try to open and fix the bad contact .

JVC Televison &... | Answered on Apr 04, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top JVC Experts

The Knight
The Knight

Level 3 Expert

76036 Answers

 Grubhead
Grubhead

Level 3 Expert

5683 Answers

Marvin
Marvin

Level 3 Expert

84543 Answers

Are you a JVC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...