GE Popular Questions, Answers, Tips & Manuals

Here are the steps to program your GE universal remote (model number 24922cl57252) to work with your Solace Air portable air conditioner:

1. Turn on your Solace Air portable air conditioner.
2. Press and hold the "Setup" button on your GE universal remote until the red indicator light stays on.
3. Enter the code "991" using the number buttons on your GE remote. The red indicator light will turn off.
4. Press the "Power" button on the GE remote.
5. Press the "Up" or "Down" button to try and turn the air conditioner off. If the air conditioner turns off, press the "Setup" button to lock in the code.

If the air conditioner does not turn off, repeat steps 2-5 with a different code from the list below until the air conditioner turns off: Solace Air Portable Air Conditioner Codes: 0277, 0363, 0364, 0365, 0403, 0454, 0455, 0456, 0457, 0474, 0475, 0494, 0495, 0496, 0497 I hope this helps!

Repairing a washing machine can be a complex and potentially dangerous task. It is recommended that you have some experience with repairing appliances before attempting to disassemble and repair a washing machine. Here are the general steps for taking apart and repairing a 1984 GE top-loading washing machine:

1. Unplug the washing machine from the power source and turn off the water supply to the machine.
2. Locate the screws that hold the control panel in place, typically found on the back of the machine. Remove the screws and carefully lift the control panel up and away from the machine.
3. Locate the cabinet clips that hold the cabinet in place, usually found at the top of the front panel of the machine. Use a flathead screwdriver to push the clips inwards and release them from the cabinet.
4. Tilt the cabinet forward and lift it up and off of the washing machine. Place the cabinet aside.
5. Locate the pump, motor, and transmission assemblies at the bottom of the machine. Check for any signs of damage or wear and tear, such as broken belts or damaged bearings.
6. If you need to replace a part, carefully remove the old part and replace it with a new one.
7. Once the repairs are complete, carefully reassemble the machine by following the above steps in reverse order.
8. Turn on the water supply and plug the machine back in to test it.

If you encounter any issues during the repair process or are unsure about how to proceed, it is recommended to seek the assistance of a professional repair technician.

The red flashing light on the circuit board of a GE washer is often an indication of an error code or fault. The error code can help diagnose the issue. Here are some common causes of a GE washer not spinning and a red flashing light on the circuit board:

1. Door lock error: Ensure the door is securely closed and latched.
2. Drive belt issues: Check if the drive belt is broken, stretched, or has come off the pulley.
3. Motor issues: The motor may have failed or the wiring may have come loose.
4. Central control unit (CCU) issues: The CCU may have failed and will need to be replaced.

If you are unable to diagnose the issue, it is recommended to have a professional technician diagnose and repair the problem as it may require technical skills and specialized tools.

Sounds like a dry joint or a failing control board. Take it in so service. https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

Did you check the bulb for continuity. It is best to get microwave ovens fixed professionally https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

Number one Tip, NEVER use self cleaning cycles. They only exist to break ovens and sell parts. Try disconnecting the mains after about 10 minutes of cool down time. If that doesn't work, you will need a service call to correctly diagnose if the lock solenoid has failed or you need a new control board.

Why You Should (Almost) Never Use Your Oven's Self ...

https://www.thekitchn.com > why-you-should-almost-n... Sep 8, 2022 - Self-cleaning, often with temperatures that go over 1000°, is a particular problem. The elements and the oven just get so hot - much, ...

Why You should Never Run A Self Clean Oven Cycle & A ...

https://www.generalappliancesvc.com > why-you-shoul... Jan 29, 2020 - With an inside temperature exceeding 500° C, and a flash point (the temperature at which items can self-combust without an ignition source) ...

4 Reasons to Stop Using Self-Cleaning Oven Feature ...

https://fixappliances.ca > 4-reasons-stop-using-self-clea... A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters at an extremely high temperature (932 F° or 500 C°) to ... ‎How Self-Cleaning Ovens Work · ‎Major Parts Damage · ‎Family Safety

It sounds like your PTAC (packaged terminal air conditioner) unit is malfunctioning. When the thermostat is set to heating mode, the PTAC should be blowing warm air, not cold air. There are a few possible causes for this issue:

1. The PTAC may be low on refrigerant. If the unit is low on refrigerant, it may not be able to properly heat the air.
2. The PTAC's reversing valve may be stuck in the cooling position. The reversing valve is responsible for switching the flow of refrigerant between heating and cooling mode. If it is stuck in the cooling position, the PTAC will blow cold air even when the thermostat is set to heating mode.
3. The PTAC's heating element may be malfunctioning. If the heating element is not functioning properly, the PTAC will not be able to heat the air.

I recommend contacting a trained HVAC technician to diagnose and fix the issue with your PTAC. They will be able to determine the cause of the problem and repair it properly.

Yes, the WR30x10093 ice maker is compatible with the GE GTS22KHPARWW refrigerator as a replacement for the WR30x10012 ice maker. It is always recommended to double-check the compatibility with the manufacturer or supplier before purchasing a replacement part.

Sounds like a power supply or an overload issue. https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

If the auger motor won't turn by hand, it's possible that it is frozen and needs to be removed and thawed out. You can try spraying it with cooking spray after it's dried out to help prevent future freezing. Before removing the auger motor, make sure to unplug the refrigerator and turn off the water supply to the ice maker. You may need to remove the ice bin and any surrounding parts to access the motor. Once you've removed the motor, you can thaw it out by leaving it at room temperature or using a hairdryer on a low heat setting. Be careful not to overheat the motor. After thawing, you can test the motor to see if it's working properly. If the motor still doesn't turn, it may need to be replaced.

I assume you are referring to the water dispenser on your GE refrigerator. To turn off the water dispenser, you can either: Press and hold the "Lock" button on the control panel until the water dispenser display turns off. This will lock all the functions of the control panel, including the water dispenser. Locate the water shut-off valve behind the refrigerator and turn it off. This will shut off the water supply to the refrigerator and disable the water dispenser. Note: If you are trying to turn off the ice dispenser, the process may vary depending on the model of your refrigerator. Some models have a separate on/off switch for the ice dispenser, while others do not allow you to turn off the ice dispenser without turning off the entire refrigerator. Please consult your owner's manual for specific instructions.

Hi There, Yes, there is a reset that you can do. First, unplug the dryer from the wall outlet. Then, press and hold the "Start/Pause" button for at least five seconds. Finally, plug the dryer back in and press the "Start/Pause" button once more. This should reset the dryer and allow it to turn on.

1. Open the dishwasher door and locate the screws on the inside of the door that hold the handle in place. There should be two screws, one at the top and one at the bottom.
2. Using a screwdriver, tighten both screws by turning them clockwise. If the screws are loose, this should fix the problem.
3. If the screws are tight and the handle is still loose, you may need to remove the handle and add a washer or two to create a tighter fit. To do this, remove the screws holding the handle in place and slide the handle off the studs.
4. Add a washer or two to each stud and slide the handle back on. Reattach the screws and test the handle to ensure it is now secure.
5. If these steps do not solve the problem, there may be an issue with the door itself,

Yes, you can use a GE Universal Remote RC24914-D to set up your Roku Express box. To do this, you'll need to find the correct code for your Roku Express device and program it into the remote. Here's how:

1. Turn on your Roku Express device.
2. Locate the "Code Search" button on your GE Universal Remote. This button is usually labeled "Code Search" or "Setup."
3. Press and hold the "Code Search" button until the indicator light turns on.
4. Enter the code 9-9-1. The indicator light will blink twice.
5. Point the remote at your Roku Express device and press the "Power" button. If the device turns off, you have found the correct code. If it does not turn off, repeat steps 3 to 5 with a different code until you find the correct one.
6. Once you have found the correct code, press the "Code Search" button again to save the code.

The codes for the GE Universal Remote RC24914-D can vary depending on the version, so it's possible that the code 9-9-1 may not work for your device. If that's the case, you can try other codes listed in the remote manual or on the GE website. I hope this helps you set up your Roku Express device using your GE Universal Remote.

This issue could be caused by the oven regulator valve not being set correctly for the altitude and fuel source. I'd suggest double-checking that the regulator is properly adjusted to the altitude and fuel source. Additionally, you may want to check the oven igniter and burner for proper operation and make sure the correct model and size of burner is installed. If you have any further questions or need help, please feel free to reach out.

If the inlet on your GE washer has been stripped or cross-threaded, it may be necessary to replace the inlet to repair the problem. To replace the inlet on your GE washer, you will need to follow these steps:

1. Disconnect the power to the washer by unplugging it from the wall outlet or turning off the circuit breaker that supplies power to the washer.
2. Shut off the water supply to the washer.
3. Remove the hoses from the inlet by loosening the hose clamps or fittings that secure them to the inlet.
4. Remove the screws or bolts that secure the inlet to the washer.
5. Carefully lift the inlet out of the washer and set it aside.
6. Install the new inlet by reversing the above steps. Make sure to connect the hoses to the correct fittings on the new inlet.
7. Turn the water supply back on and check for any leaks.
8. Restore power to the washer by plugging it back into the wall outlet or turning the circuit breaker back on.
9. Test the washer to make sure it is filling properly with the new inlet.

Note: These instructions are general guidelines and may vary depending on the specific model of your GE washer. If you are unsure of how to replace the inlet on your washer, it is recommended that you contact a qualified appliance repair technician for assistance.

Buy a new one based on the size https://www.ajmadison.com/cgi-bin/ajmadison/MBBS.html https://www.google.com/search?q=Thermador+Microwave+MBBS+replacement ..