GE Ovens - Recent Questions, Troubleshooting & Support


This means that the Sabbath mode has been enabled. To disable the program, first press and release the Cancel/Off to stop the current programmed bake settings. Then press and hold Settings until Sabbath Mode Off is displayed. See page 14 of the manual for setting the Sabbath mode. The manual is available on the product page: https://www.geapplianceparts.com/store/parts/assembly/C2S995SEL1SS . The current link to the manual is https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-85241.pdf . Most GE oven codes are listed here: https://www.geappliances.ca/en/support/knowledgebase/range-oven-function-error-or-fault-codes . The Sabbath Mode symbol is shown at the bottom of the table.

This mode can be used to set the oven temperature for an extended bake (usually for a low temperature) or a programmed bake. It's used by those who strictly keep the Sabbath but want a hot meal ready when the Sabbath ends.

I hope this helps.

Cindy Wells

GE Ovens | Answered on Oct 06, 2019


I have an FA code as well. Dont know what it is. Everytime it comes on I clear it and it comes back. Not using oven, just cook top

GE Profile JT955... | Answered on Sep 19, 2019


https://getsatisfaction.com/gebrillion/topics/ge-double-oven-e97-code

Two posters at the internet link above had suggestions. The following doesn't cost to try:

"Karl McHugh
  • 1 Post
  • 1 Reply Like
you guys are going to laugh at this. have this problem. my repair guy gave me a tip until I can figure out long term....open bottom oven...there are vents at the top. use a flashlite and look in back right corner and you will see a squirrel cage fan. I taped together two long skewers to reach the back...insert through vent to squirrel cage fan and spin a few times. bingo...f code goes away and oven goes back to normal. don't want to do this long term but works until you get a solution. Ive been doing it for a month now but I travel all week and haven't had a chance to get it repaired. this has worked every time...seems like a dead spot in the drive for this???"

GE Ovens | Answered on Sep 09, 2019


GE Ovens | Answered on Aug 18, 2019


use stop/clear reset clock then

GE Profile JT915... | Answered on Jul 22, 2019


I, too, have lost my manual and none of the timers work. I can never remember how long to run the clean cycle for, but will turn it off as it has been a little over 2hours and your post mentions 1.5hours.
I initiate the cleaning cycle by completing steps mentioned above and then turning the top dial (which has a clean range on it) clockwise until the clean light comes on. I then just time it by my watch to turn it all off. Then I wait a couple of hours before attempting to open the door. Don't forget to take the racks out, they are not suppose to go through the Clean cycle.
Good Luck,
Linda

GE JKP15... | Answered on Jul 12, 2019


Pull the door completely off and re-insert the door on the hinge supports.

GE Ovens | Answered on Jul 12, 2019


  • Open internal fuse
  • Magnetron failure
  • Control board failure
  • Door interlock failure

GE Ovens | Answered on Jul 12, 2019


Sometimes one must simply accept things as they are...

GE Ovens | Answered on Jun 24, 2019


I, too, have the GE -JKP86. Microwave over oven. My oven would not heat up on bake or broil. Elements checked good, no fault codes. This is how I fixed mine: Shut off power at the box. Remove unit from cabinet. I placed mine on a chair. Remove cover(s) until you expose the circuit boards behind the control consol . The top board is behind the microwave controls, the bottom is behind the oven controls. Remove the bottom board by removing 4 screws. I take pictures with my smart phone, even some video. Helps me remember how everything goes back together. BE SURE THE POWER IS OFF, HIGH VOLTAGE IN HERE! One of the screws is hard to see. It is behind the ribbon connector. Unplug everything carefully. You will see a red and an orange wire north and south of a small relay. You must unclip the circuit boards from each other. Look for a missing drop of solder on the back side of the board with the relay. You will find it underneath where the red wire connects. Mine ( looking through a magnifying glass) looked like a crater with a wire sticking up out of it. It had overheated and the solder dripped out. The joint is inadequate. I cleaned and resoldered it with a nice blob. Reassemble and check. I just left mine on the chair. Power on. Select bake, 300, start. You should here the relays click and after about 45 seconds you'll see the bottom element glow. After one minute the relay clicks again ant you'll see the top element glow. They alternate during the preheat cycle. Put it all back together and shove it all back in the hole. Hope this helped!

GE JKP86... | Answered on Jun 24, 2019

Not finding what you are looking for?
GE Logo

3,650 questions posted

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

William Miller
William Miller

Level 3 Expert

9174 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...