Pool & Spa - Page 2 - Popular Questions, Answers, Tips & Manuals
How to change the LED colour on The Orbis by Rotospa?
On the control unit select the 'up' arrow to cycle through the LED lighting options. Some units will only have one option (Blue) while other models will have a spectrum of colours to select from. Control unit diagram illustrated here https://www.hottubhiremerseyside.co.uk/faqs/
10/11/2023 2:11:02 PM •
Pool & Spa
•
34 views • 1 helpful votes
New XtremepowerUS 2HP In-Ground Swimming Pool Pump Variable Speed 2 Inlet 230V High Flo w/ Slip-On Fitting, i turned it on after 2 mins switch from high to low then shut off and get very hot.
All electric motors run hot and pool pumps are no different. But how hot is too hot for a pool pump? The first test is simply whether you can touch the motor or not. Under normal operating conditions, the motor end of the pump is hot enough that you can barely touch it - but not searing hot.Best to you.https://www.google.com/search?q=XtremepowerUS+2HP+In-Ground+Swimming+Pool+Pump+Variable+Speed+running+temp&newwindow=1&sxsrf=AB5stBhpriuNhnfXLYYTg7tuS-LWwW262g%3A1690815381903&source=hp&ei=lcvHZKH_NOHi9AOquJjADw&iflsig=AD69kcEAAAAAZMfZpVdAAi94QXZiwKfN3nArsWv-Gm1z&ved=0ahUKEwjhnd6RmrmAAxVhMX0KHSocBvgQ4dUDCAo&uact=5&oq=XtremepowerUS+2HP+In-Ground+Swimming+Pool+Pump+Variable+Speed+running+temp&gs_lp=Egdnd3Mtd2l6IkpYdHJlbWVwb3dlclVTIDJIUCBJbi1Hcm91bmQgU3dpbW1pbmcgUG9vbCBQdW1wIFZhcmlhYmxlIFNwZWVkIHJ1bm5pbmcgdGVtcEgAUABYAHAAeACQAQCYAQCgAQCqAQC4AQPIAQD4AQL4AQE&sclient=gws-wiz#kpvalbx=_sMvHZMuPJPez0PEP3M2LgAY_44
What does U16 mean on my intex hot tub
limited info generic answer u code doesnt show for intex their codes usually start with E this is a manual that has the trouble shooting on page 20 ------- https://www.manua.ls/intex/purespa/manual?p=1 --------- and pg 13 has the codes
How can I test if my Hayward gas heater water pressure is working??
Testing the water pressure of your Hayward gas heater is a relatively simple process. Follow these steps to check if your water pressure is working properly:
- Turn off the Gas Heater: Before performing any tests, make sure the gas heater is turned off to avoid any potential accidents or injuries.
- Check the Pressure Gauge: Locate the pressure gauge on your Hayward gas heater. It is usually located on the front panel of the unit or near the plumbing connections.
- Observe the Pressure Reading: The pressure gauge will display the current water pressure. It is typically measured in pounds per square inch (psi). The optimal water pressure for most pool heaters is usually between 15 psi to 25 psi, but it's essential to check your heater's manual for the specific recommended pressure range.
- Turn on the Pool Pump: Ensure that the pool pump is running, as it is responsible for circulating the water through the heater. The water pressure will be at its most accurate when the pool pump is operating normally.
- Monitor the Pressure: While the pool pump is running, observe the pressure gauge to see if the water pressure falls within the recommended range. If the pressure is below the minimum recommended level, it may indicate a circulation issue or a problem with the pool pump.
- Check for Leaks: While testing the water pressure, inspect the heater and the surrounding plumbing connections for any signs of leaks. Leaks can lead to reduced water pressure and affect the heater's performance.
The controller for my Prowler 920 will NOT turn on. It flashes a few of the lights on and off but will not power up so I can run the Prowler to clean my pool
If the controller for your Prowler 920 robotic pool cleaner is not turning on or powering up properly, here are a few steps you can take to troubleshoot the issue:
1. Check the Power Supply: Ensure that the power supply is properly connected to the controller and that it is receiving power. Verify that the power cord is securely plugged into a functioning power outlet. You can try plugging another device into the same outlet to confirm that it is working correctly.
2. Inspect the Controller Display: Take a close look at the display on the controller. If any error codes or messages are displayed, consult the user manual or contact the manufacturer for further instructions on how to resolve the specific issue indicated.
3. Reset the Controller: Try performing a reset on the controller. Look for a reset button or a combination of buttons to press and hold simultaneously for a few seconds. This action can often help resolve minor software glitches and restore the controller's functionality.
4. Check for Loose Connections: Ensure that all cables and connections between the controller and the power supply or the Prowler unit are securely plugged in. Sometimes, a loose or faulty connection can prevent the controller from turning on.
5. Replace Batteries: If your controller uses batteries, make sure they are not depleted. Try replacing the batteries with fresh ones and see if the controller powers up properly.
6. Contact Manufacturer Support: If the above steps do not resolve the issue, it's recommended to reach out to the manufacturer's customer support. They can provide you with further assistance, troubleshooting steps, or advise on any potential repairs or replacements that may be needed.
Remember to consult the user manual that came with your Prowler 920 for any specific troubleshooting steps or contact information for customer support.
5/22/2023 9:23:13 PM •
Pool & Spa
•
156 views • 0 helpful votes
Not finding what you are looking for?