Error code E732-001 controller main pcb - Canon imageRunner C3100 Copier

Canon iR3300 Error Codes Code: E732-0001

Code

E732-0001

Description

A fault is detected by the main controller PCB in the communication between reader controller PCB and the main controller PCB

Causes

The connector has poor connection. The reader controller PCB is faulty.

Remedy

1. Connector, Reader controller PCB Is the connection between the connector J1014 on the main controller PCB and the connector J409 on the reader controller PCB normal? NO: Correct the connection. YES: Replace the reader controller PCB.

Below is the site this came from which lists all the error codes in case another occurs after you resolve this one


Canon iR3300 Error Codes List page 1 from 12

an error has occured in communication between fax controll PCB and main controller PCB.Check the connection of the cable between the fax controll PCB and main controller PCB.rEPLACE THE rom dimm of the fax control PCB.Replace the fax controlPCB.Replace the main controller PCB.

Error code E000733-0001 on Canon IR2200

E733-0001 means a fault is detected by the main controller PCB in the communication between the DC controller PCB and the main controller PCB.

Main cause: The connector has poor connection. The DC controller PCB is faulty.

Solution:

Verify the connection between the connector J1015 on the main controller PCB and the conductor J316 on the DC controlled PCB is normal.
Correct the connection if necessary.

The connection is correct: Replace the DC controller PCB.

The reader controller PCB detects communication error between the main
controller PCB and the reader controller PCB.
Disconnect and then connect the reader communication cable
connector, Replace the reader controller PCB, Replace the main
controller PCB

E732-0001 Error Code: Reader Controller PCB is faulty

[ Case in the field ]
Description
E732-0001 can be displayed when a communication error occurs.
Cause
In the field, this symptom occurred because the Reader Controller PCB was faulty.
Field Remedy
1. Make sure that the connector between the host machine and the reader unit is securely fitted.
2. Make sure that the connectors on the Reader Controller PCB are securely fitted or there is no pinched cables.
3. Remove and insert the Main Controller PCB (Sub) from the Main Controller PCB (Main). If the symptom still recurs, go to the Step 4.
4. Replace the Reader Controller PCB with a new one.


E732-0001 Error Code: locks up during copying

E732-0001 can be displayed when a reader communication error occurs.
Cause
As a result of inspection, it was found that this symptom occurred because of poor soldering of J1302-34pin on the Main Controller PCB (Sub).
Field Remedy
1. Make sure that the connectors are securely fitted between J1302 on the Main Controller PCB (Sub) and J502 on the Reader Controller PCB and that
there is no pinched cable.
2. If no problem is found, replace the Main Controller PCB (Sub) with a new one.


E732-0001 Error Code: Because of poor contact of SDRAM

Description
E732-0001 indicates that a reader communication error has occurred.
Field Remedy
As a result of inspection, it was found that this symptom occurred because the SDRAM was not securely fitted on the Main Controller PCB. So, remove
and insert the SDRAM once again.

Similar to Description The 24V output from the composite main power supply PCB is absent for 1 sec or more Causes The wiring is faulty (short circuit, open circuit). The composite power supply PCB is faulty. The DC controller PCB is faulty. Remedy 1. Connectors Are the connectors J204 on the main power supply PCB and the connector J300 on the DC controller PCB connected securely? NO: Connect the connectors securely. 2. Main power supply PCB Is 24 V supplied by the main power supply PCB (J204) to the DC controller PCB (J300)? (J204-5 <-> J300-5: OVU3, J204-6 <-> J300-6: OVU3, J204-7 <-> J300-7: 24VU3, J204-8 <-> J300-8: 24VU3) NO: Replace the main power supply PCB. YES: Replace the DC controller PCB.

I’m happy to help further over the phone at https://www.6ya.com/expert/joshua_ac64e182ed26f66d

E351: Error PCB ECO. Communication error between the PCB and the PCBECO main driver during startup.

Turn off main power and check the main controller PCB (primary, secondary), thenturn the main power.

Check in the back of the machine the main controller PCB (Main) make goodconnection with the PCB ECO-ID: help with image processing.

Hoping this is helpful message ... GOOD LUCK

E732-0001 Error Code: Reader Controller PCB is faulty

[ Case in the field ]
Description
E732-0001 can be displayed when a communication error occurs.
Cause
In the field, this symptom occurred because the Reader Controller PCB was faulty.
Field Remedy
1. Make sure that the connector between the host machine and the reader unit is securely fitted.
2. Make sure that the connectors on the Reader Controller PCB are securely fitted or there is no pinched cables.
3. Remove and insert the Main Controller PCB (Sub) from the Main Controller PCB (Main). If the symptom still recurs, go to the Step 4.
4. Replace the Reader Controller PCB with a new one.


E732-0001 Error Code: locks up during copying

E732-0001 can be displayed when a reader communication error occurs.
Cause
As a result of inspection, it was found that this symptom occurred because of poor soldering of J1302-34pin on the Main Controller PCB (Sub).
Field Remedy
1. Make sure that the connectors are securely fitted between J1302 on the Main Controller PCB (Sub) and J502 on the Reader Controller PCB and that
there is no pinched cable.
2. If no problem is found, replace the Main Controller PCB (Sub) with a new one.


E732-0001 Error Code: Because of poor contact of SDRAM

Description
E732-0001 indicates that a reader communication error has occurred.
Field Remedy
As a result of inspection, it was found that this symptom occurred because the SDRAM was not securely fitted on the Main Controller PCB. So, remove
and insert the SDRAM once again.

E733
0001 A fault is detected by the main controller PCB in the communication between
the DC controller PCB and the main controller PCB.
Main cause The connector has poor connection. The DC controller PCB is faulty.
Action
1. Connector, DC controller PCB
Is the connection between the connector J1015 on the main controller PCB
and the conductor J316 on the DC controlled PCB normal?
NO: Correct the connection.
YES: Replace the DC controller

that mean low power or The 24V output from the composite main power supply PCB is absent for 1 sec or more.
Main cause The wiring is faulty (short circuit, open circuit). The composite power supply PCB is faulty. The DC controller PCB is faulty.
Making Corrections
1. Connectors
Are the connectors J204 on the main power supply PCB and the connector J300 on the DC controller PCB connected securely?
NO: Connect the connectors securely.
2. Main power supply PCB Is 24 V supplied by the main power supply PCB (J204) to the DC controller
PCB (J300)?
(J204-5 <-> J300-5: OVU3, J204-6 <-> J300-6: OVU3,
J204-7 <-> J300-7: 24VU3, J204-8 <-> J300-8: 24VU3)