Fisher and Paykel GWL11 Top Load Washer Logo
Anonymous
Anonymous Posted on Oct 05, 2011
Answered

Water starts and stops, over and over again when filling. After some time, we get trouble beeps and 2 yellow lights, 1 near either end of progress indicator. Machine is a GWL11

Answer This Question

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Brigadier General:

An expert that has over 10,000 points.

  • Master 6,277 Answers
  • Posted on Oct 05, 2011
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Brigadier General:

An expert that has over 10,000 points.

Joined: Jan 22, 2011
Answers
6277
Questions
0
Helped
1026618
Points
20216

Hi from retired Englishman in SW France,

If you have checked that the hot and cold water taps are turned on fully and the hoses are not kinked or squashed at the back, it is worth while checking both the hot and cold water inlet filters. Turn the taps off and remove both hoses at the washer end. Inside each inlet port there is normally a little filter which should just slide out. Clean if necessary and replace each one and the hoses. If after turning the taps back on there is no improvement, the problem is symptomatic of a malfunctioning hot or cold water control valve. Sorry but it needs a service call and a check that it isn't the control PCB ;-0(

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck,
John C

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Why my AEG F55080vi stops after drain cycle (program beginning) and then it stops and I hear 2 beeps and 2 flash continuously?
Definitely, water drain time-out. Error code i20.
The pressure switch doesn't return to EMPTY (1-2) after two drain phases lasting 120 seconds.
Possible causes:
Drain circuit obstructed/blocked; drain pump
interrupted or jammed (foreign bodies); level
pressure switch blocked on FULL (1-3); hydraulic
circuit of pressure switch obstructed; wiring faulty;
circuit board faulty.

Thanks to your detailed description of failure I conclude that in drain phase (after starts drain pump) leaks water and causing a short circuit. I would thoroughly reviewed drain hydraulic circuit. If is alarm displayed and there is no water inside dishwasher then check heater and anti-interference suppressor.

Dado
Read full answer
Jul 12, 2014 • AEG Dishwashers
0helpful
1answer

Fisher and paykel smart drive 608 6.5 kgs has running well for ages but recently while finishing water filling it makes a warning beep sound and start leaking from the bottom,anyone there to help me pls
Hi just read your post.Now when the machine beeps a series of lights will light up on the wash progress lights. The spin light is number 8 and the other end of the lights is number 1 which is long wash, i think. Starting from the long wash light which is number 1, which lights are on when the machine is beeping, is it 1,4 and 7 or 3, 7 and 8 etc? Please reply with the answer to this question and i am sure i can help you. Regards Lu
Read full answer
Jan 25, 2014 • Fisher and Paykel Fisher & Paykel Washer
0helpful
1answer

Fisher paykel smart drive 601
Hi just read your post.When the machine beeps a series of lights will light up on the wash progress line of lights. Staring from left to right the long wah is number 1 and the spin light is number 8 which lights sre on when the machine beeps, is it 2, 4 and 8 or 1, 3 and 7 etc.Please reply with this information and I sure I can help you. Regards LU
Read full answer
Jan 24, 2014 • Fisher and Paykel Fisher & Paykel Washer
0helpful
1answer

Model Gw709AU
When you start your machine is the water just go stop go stop,
Just wait for the machine to display an error code on the wash progress lights and beeps constantly.
It could be the Rotor Position Sensor, out of balance switch or lid magnetic reed switch.
Your error code will determine this.
Is your machine beeping & showing a weird pattern of lights on the wash cycle, It is displaying an error code,
To read this error code you start at the red spin light & work to the left only add up the lights that are on. Red spin light = 1 2nd rinse light =2 1st rinse light =4 last wash light=8 4th wash light=16 3rd wash light=32 2nd wash light=64 1st wash light=128
j8paojvh5jrgaaaaabjru5erkjggg==

2_26_2013_3_17_31_am.jpg
Read full answer
Feb 20, 2013 • Fisher and Paykel Washing Machines
0helpful
1answer

Washing machine doesnt work kelvinator smartdrive 085 0.5kg
you have to check 1- water pressure switch (wps) , 2- the hose which fixed between wps and drum may disconnected or broken.
Read full answer
Jun 12, 2017 • Kelvinator Washing Machines
0helpful
1answer

It has an F1 error code. It will start the water flow for about 2 seconds. Stops and beeps f1 on the screen. I hit the stop button and start again and have to repeat this 3 times before the wash machine...
The manufacturer has issued a remedy for the F-1. What you do is empty the machine of water and unplug it. Open the control panel and remove the pressure hose. Blow out the hose to remove sediment . Re secure it to the control and retry. No parts needed. F-1 Error infothemobilian_1223.jpg

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Read full answer
Feb 01, 2011 • Kenmore Oasis HE 27082 Top Load Washer
1helpful
2answers

Solid amber light ON Dell Inspiron 530 desktop.The Fans start and stop immediately.The mother board has the power ON Amber light.
The Yellow Light of Death, anyway turn on Your PC, as it starts You will here some beeps especially on a Dells. Count the beeps , there will be a slight pause so it will beep once then pause then beep again. Count the beeps and that will be Your code. Go to Dell Support site and look up code. Most of the time a Yellow amber light means that there is trouble with Your Motherboard but thats not to say its the Motherboard itself, it could have possibly burned out Your RAM, Processor, Heat fan, even the power supply itself. So look up the code and at least You'll have a better chance of finding the solution, Good Luck
Read full answer
Mar 04, 2010 • Dell Inspiron 530 Desktop Computer
0helpful
1answer

Top loader washer won't fill with water
Either the water level sensor is faulty or the selector switch is bad.



Servicing the Water Level Control Switch

This is another control panel switch, usually located next to the temperature switch. There is a small hose connected to this switch, and sometimes this hose becomes loose and falls off the connection. When this happens, the water in the tub usually overflows. To solve this problem, cut about 1/2 inch off the end of the hose and use a push fit to reconnect it to the switch.

The switch itself can also malfunction, resulting in tub overflow and other water-level trouble in the tub. If you suspect this switch is faulty, remove it by backing out the screws holding it in place. Take it to a professional service person for testing. If the switch is faulty, replace it with a new one of the same size and type. Connect the new switch the same way the old one was connected.
Read full answer
Oct 01, 2009 • Washing Machines
0helpful
3answers

GLW10US won't do anything but beep
well i don't have any experience with this brand but i would say you need to change the fill switch it senses how much water is in the tub shuts the water off then starts the washer its also called the pressure switch
Read full answer
Feb 16, 2008 • Washing Machines
0helpful
1answer

Zanussi FX1465W aquacycle, beeps 5 times and end light flashes
I have the same trouble with my washing machine did you find a solution i have been told the PCB or motor drive system
Read full answer
May 19, 2007 • Zanussi FJS1225W Front Load Washer
Not finding what you are looking for?

View Most Popular

GWL11 Top Load Washer

  • Washing Machines

Related Question

Why my AEG F55080vi stops after drain cycle (program beginning) and then it stops and I hear 2 beeps and 2 flash continuously?

  • AEG Dishwashers

Related Topics

44 views

Ask a Question

Usually answered in minutes!

Popular Questions

Error code 37

Fisher and Paykel Fisher Paykel...

Washing machine won't turn on

Fisher and Paykel (IWL12)

Washing machine not draining and finishing cycle

Fisher and Paykel GWL11 Top Load...

Blocked filter in Fisher & Paykel washing machine top loader

Fisher and Paykel IWL12 Top Load...

Error code 130 & 240 how do i fix this

Fisher and Paykel Fisher Paykel...

Top Fisher and Paykel Washing Machines Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...