20 Most Recent Frigidaire 30 in. Electric Gallery Series Self-Cleaning Double Wall Oven - Page 4 Questions & Answers

Enter the model number into the search box at
http://www.frigidaire.com/manuals

Control panel/computer mother board is bad, needs replace. You can order almost any appliance part online or threw Sears. Write down the model number and type of oven and go from there. They carry countless brands of appliance parts. You'll be amazed at what you'll find at Sears. They'll have it or either have to order it for you. Trace your steps when removing the face panel and follow your wire connections. Relatively quick job. 30-60 min job. Lowes, carries appliance parts you can order as well.

this happens alot,, im guessing you took it out by taking the two screws out and pulling it through,, sometimes the wire comes off before it makes it through the hole, you have to take the unit out and take the back panel off to get to it and plug it back in

try turning your breaker off for 20 minutes, then try it again,, if this does not help it could have burnt out a element or the main board has went out,,, also make for sere you are getting the full 220 volts to the unit,, this will involve taking the unit out

Frigidaire dishwasher will not work at all it has PF blinking

The probe might be out of spec and therefore the control is not getting a correct reading and thinks everything is fine. That probe is also known as a sensorMight just be corrosion in the sensor's connector. Sometimes bypassing it entirely fixes the problem. Now about the steaming issue:
Convection motor not circulating the air properly?
I would check that.

American oven fault codes and manuals HERE If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

is there a time bake or something similar on it,sounds like it's stuck on that cycle,next time send the model number,could have a bad touch pad or clock assy. stuck on a time cycle so no matter what you do it's counting down

because frigidaire codes only go to f9 i can't see what is going on . now if ist F O or F 1 then its a clock or what is a E O C electronic oven control . .. also behind the control is a tech sheet that will help you to see what the code means . so read the panel and then ck the tech sheet for info .. hope this helps mm feed back pleas mm

Your range sounds like it is need of an oven igniter .over time the igniter can become weak and it looks like it is glowing but the part itself is not pulling enough amperage to open your gas valve, this is a safety feature I would start there those parts generally run less than 100 bucks!

thanks for using fixya....

Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor goingbad...

Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

Hi

Please check this links as per your query :-

http://www.repairclinic.com/Range-Stove-Oven-Troubleshooting#Itsstoppedcompletely_electric

Please accept the solution if it's helpful. Do get back to us for any further query.

Thanks for contacting fixya.com

Hi,

Error R or F7 as its technically called on your Frigidaire 30 in. Electric Gallery Series Self-Cleaning Double Wall Oven means that the keypad is shorted or stuck and to resolve this issue you’ll have to replace the electronic range control (ERC).

Let us know if you have something more to know else accept the suggestion.
Thank You for contacting Fixya.com

The only thing that I can suggest to you is to locate the breaker for the stove in the breaker box and turn off the power. Leave the power off for at least a minute. This will reset the oven to factory defaults.
Once you turn your breaker back on you should be able to open the oven.

Hi,
If your electric oven is not heating then you probably have a bad heating element in your oven. This is not that hard to fix yourself...
Check out this tip that I wrote about the Oven not heating problem..

Oven Problems Electric Oven is Heating Slowly or Poorly
http://www.fixya.com/support/r4511800-oven_problems_electric_oven_heating

heatman101

yes....order the bar and screws and put them in.

Check to see that the convection element is heating. If not, ohm it out, either the element is bad or it is not getting power from the control.

hello,

All Frigidaire Electric Gallery Series carry out same function when working it pull dust that are around can not be easily see with eye (micro dust) around throngh the air ventilation when it plug on to power .

what you are to do always after use is to clean it very well in other to avoid the accumulation of the dirt to avoid damage of element (HEAT PTOVIDER)hope this help.

thank you and thanks for using fixay.

There is a safety thermostat (thermal fuse) on the back wall of the oven that interrupts power from L1 to the Bake and Broil elements. This fails open on an over-temperature or over-current condition. The oven needs to come out of the wall to replace it - best left to a tech unless you are experienced in such things.

Best Regards,
Bruce
www.fixyourboard.com