Top 20
Hannspree (K206-10U1-005) Television Questions & Answers
Hannspree tv is making a buzzing sound
First I am glad helped with the other issue.This issue needs to be defined: do you hear the buzz when sound is at zero? I not the issue is in audio circuit or signal to set----If you hear the buzz with sound off it is likely something in the set vibrating hard enough to make the noise.What causes this is a part that is not bad but noisy--there are ways to deal with this depending on set.My real concern is if set is opened etc it will void your warranty!If 5 days old most major stores will take it back or issue credit so you can replace the set----makers will often play a shell game--tell you it MUST go in for repair.Most major stores have an unwritten rule here: set can be returned within first 30 days and exchange/replaced for ANY reason.Seen ones returned because owner did not like the color of the cabinet etc.If I know what type of set it is (has a picture tube, LCD etc and you have no warranty I can tell you what to look for and a possible way to fix it---Don't void the warranty if you have one by just opening it.Saw a (will not call him stupid) person with a 1,000 set here yesterday which clearly had a problem and was 3 days old open the set and in doing so removed the labels there to indicate if someone has tampered with the set---now he has no warranty and a non working set.
5/1/2012 11:12:26 PM •
Hannspree...
•
596 views • 1 helpful votes
My 32inch tv turns on but the picture is wired.
On a 32 inch it may not be worth fixing--not going to be a reset etc--base decision on fact that possible repair should not exceed used value of set--which in my view it likely will.
5/26/2012 4:09:17 PM •
Hannspree...
•
137 views • 0 helpful votes
I have built in Freeview
This tv is a flat LCD tv wright?Not a big bulge back CRT tube tv,If this is CRT tv is analoge design tv dosen't have freeview Digital Tuner inside of the tv.If it is a flat LCD tv.Make sure ur setting for retuning not on CALBE SETTING.Make sure ur tv setting are AIR SETTING and have good Digtial antena will get a stronger signal get all the free AIR broadcasting stantoins channels,a good strong Digital antenna design does make big a different.
8/4/2011 2:00:20 PM •
Hannspree...
•
652 views • 0 helpful votes
Subtitles will not switch off
Whilst on TV Mode:
Open the menu and go to features then subtitle.
Switch off analogue subtitle.
Scroll to 1st subtitle and then scroll through the languages until "off" comes up.
Repeat for 2nd subtitle.
Hey bloomin presto!!! They gone!!!!!!! :-)
8/9/2011 7:59:09 PM •
Hannspree...
•
392 views • 1 helpful votes
When my hannspree tv goes
I assume it is the capasitors in Powersupply that is the problem. It is eleven of them, and worth trying to change them.
5/21/2011 4:48:35 PM •
Hannspree...
•
454 views • 3 helpful votes
I have a 42" LCD
If they are all coming from the same physical source (please clarify) there is little you can do other than to look in thge audio menu of the TV and switch on auto volume if your particular model has that option.
I hope I have been of help but please do not hesitate to ask if you have any further questions.
I appreciate your vote if you appreciate my reply.
2/24/2011 6:00:57 PM •
Hannspree...
•
151 views • 1 helpful votes
My Hannspree TV volume goes
there's no faulty parts on your unit but sure that you have a dry joints on the sound amplifier section.
Look for a qualified technician to re-solder for a dry joint on the said section and it will fix the problem.
If you have knowledge in soldering then open the back panel of your tv.
Then observe first because you have to pull-out some connector from the main board.
Remember that anything you pull-out will be back to their position as you finished resoldering.
Try to trace the connectors of your speaker to the main board.
It is connected to ic which have a heat sink.That's the sound amplifier ic.
Find the cold solder around there then resolder it.
You can try the tv, if you hit the cold solder then intermittent sound will be cured.
Remember that before you try turning on the unit be sure that you returned the connectors to its original position. gud luck buddy...
Thanks for using fixya...
1/9/2011 2:58:25 AM •
Hannspree...
•
370 views • 0 helpful votes
Whenever I change the volume, it also changes the
Is the source button on the remote near the volume button? If so I suspect a faulty remote.
or ...Are you using a universal remote or the original?
I hope I have been of help but please do not hesitate to ask if you have any further questions.
I appreciate your vote if you appreciate my reply.
2/27/2011 11:56:30 AM •
Hannspree...
•
68 views • 0 helpful votes
Hi i have a blue
Please clarify how you are feeding the TV, is it from the aerial (antenna) or cable, or using a scart lead etc. It sounds like it is not seeing the video input but is seeing the audio. If it is from a scart lead the lead may be faulty, or if some other route then please clarify.
I hope I have been of help but please do not hesitae to to ask if you have any further questions.
I appreciate your vote if you appreciate my reply.
1/31/2011 10:11:28 PM •
Hannspree...
•
130 views • 0 helpful votes
My 25" comes on for 5 sec and then turns off
that is the main board the tv has a faulty solder it is turning of to save any more damage a repair service would charge 50 pounds tops i hope this helped and please be sure to make payment thanks if u need more info don't hesitate in contacting me
1/16/2011 8:00:38 PM •
Hannspree...
•
76 views • 0 helpful votes
There's a red line on the right side
Your TV has start to deteriorated.
Prolonged this condition will make your screen out of light and totally dead.
If you don'y familiar with TV repair, kindly have the TV get fix in shop
11/24/2010 4:52:54 PM •
Hannspree...
•
172 views • 1 helpful votes
Where are hannspree tvs made
Hi
There website isn't specific where there products are made but I would guess China. They have divisions all over the world.
6/6/2010 12:41:35 AM •
Hannspree...
•
1,842 views • 3 helpful votes
Not finding what you are looking for?