Hannspree Recent Questions, Troubleshooting Help & Support

The weight of the Hannspree HSG1074 24 inch LCD HDTV is approximately 8.8 pounds (4 kg) without the stand. However, the weight may vary slightly depending on the specific model and any additional accessories that are included with the TV. If you need more precise information, you may be able to find the weight listed on the product specifications page on the Hannspree website or in the user manual that came with the TV.

The issue you are experiencing with your Hannspree 42 LCD TV could be caused by a few different things, such as a loose cable connection, a faulty T-con board, or a defective panel. Here are a few steps you can try to troubleshoot the issue:

1. Check the cable connections: Make sure that all the cables connected to your TV, especially the ones connected to the right side of the TV, are firmly plugged in.
2. Power reset: Try turning off your TV and unplugging it from the power outlet for at least 10-15 minutes, then plug it back in and turn it on again.
3. Swap inputs: If you are only experiencing the ghosting on one input, try swapping the input with another one to see if the issue persists.
4. T-con board: If none of the above steps resolve the issue, it is possible that the T-con board is faulty. The T-con board controls the timing of the image displayed on the screen and is often the culprit of ghosting issues. A technician can diagnose and replace this board if necessary.
5. Panel: If the above steps don't resolve the issue, it is possible that the LCD panel itself is defective. This is less common but can happen over time. Unfortunately, replacing the panel can be costly and may not be worth it on an older TV.

If none of the above steps resolve the issue, it may be best to contact a qualified technician to diagnose and repair the issue.

To program a Hannspree remote to a Hannspree TV, first turn on the TV and then press and hold the "Code" button on the remote until the LED light turns on. Next, enter the four-digit code for the TV using the number keys on the remote. If the TV turns off, press the "Code" button to save the code. If it doesn't turn off, try another code until you find one that works. If you cannot find the four-digit code for your Hannspree TV, you can try using the code search feature on the remote. To do this, follow the steps for programming the remote but instead of entering a code, press and release the "Code" button and then press the "Power" button repeatedly until the TV turns off. Then, press the "Code" button to save the code. If you are having trouble programming the remote, make sure you are aiming the remote directly at the TV and that you are not too far away. Also, check that the batteries in the remote are fresh and properly installed. If you accidentally program the remote to the wrong TV or if you want to program it to a different TV, you can reset the remote to its default settings by pressing and holding the "Code" button for at least three seconds until the LED light turns off. This will erase any previously programmed codes.

Question moved from Cellphones. It is broken, but try a power reset. Disconnect the mains power at the wall outlet for 5 minutes. https://www.fixya.com/support/r29790007-repairing_own_television ..

Normally the HDMI cable input for your Cable set top box. They are numbered. However, you can just scroll through until the picture appears.

It is not compatible. The 42" requires upscalling and the 19" hasn't got upscalling.

do you mean if you hooked up the tv with the aerial antenna can not get any channel? ok if just a white raster only and doesn't scan or tuned even manually and auto search, the cause is bad tuner.

Hi there, It is very easy to restore your tablet once you know what to do. Turn your tab off (after you back-up everything you want to keep) Wait till the tab is completely off. Press and hold the Volume down button together with the power button. release after you see the logo. Then it will start up into a weird looking "recovery mode". Scroll down to 'wipe data/factory reset' and press the powerbutton. follow instructions and after complete it will take a while to start up for the first time again. all done!

hi try to un plug and re installed 10 to 15 time some time their is a problem with female jack

check the batteries in remote .

To do a factory reset, you have to enter its Service Mode. If you wish to get some details; check the sites linked here. https://elektrotricks.blogspot.com/ https://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done. NB: Please read and understand well, the instructions to enter the service mode, before you begin. Be very careful. Note how to "EXIT" the service mode; after entering and adjusting data. This is very important Search the site by type in the Brand Name of your set, in its search bar at the right side column, and press enter. See it in by Webview with mobile or by desktop. Mobile View has no search box.

Try different unlock patterns. Once it rejects you it will ask you to sign in to your google account. Type "null" in the user name line and "0000" for the password. I was locked out of my android phone and used this to get past the unlock pattern and back in to my phone.

Sounds like system memory fault. Contact any service technician to make it sure. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

call them only they can do that. also most web sites no ban hacking passwords because of NEW LAWS. but here there are ask them they designed it and no 2 PC reset the same why (all are different) https://www.hannspree.eu/support/

Might be one of two things. Check if there is any damage to screen if not the video curcit is bad

Hi, If you switch the screen off and back on again do you see a picture for a second or not? If you do then I suspect a fault called "Bad Caps" which is repairable. If not then try another screen and see if that works ok.