Top 20 HP LaserJet M4345 MultiFunction Printer Questions & Answers

Hi, Resetting the HP LaserJet Pro M1536dnf accomplishes the following:

• Clears all data from the printer's memory (including unprinted data, downloaded fonts, and macros).
• Stops any printing that is taking place and ejects the page.
• Removes some error conditions.
• Resets the printer to its factory default settings.

Reset Procedure:

• Turn off the printer
• Press and hold the Left arrow & Cancel while you turn on the printer
• Once you see Permanent Storage Init you can release the buttons.
• The printer should now start resetting.

Thanks, HP Printer Support

You're in luck! That was previously answered here: http://www.fixya.com/support/t9598231-error_49_4c2f_continue_restart

Try initalizing the Harddrive if that doesn't work. Try replacing the scanner controlboard or the DC controller. Or if the MFP is in a dusty room try cleaning the lenses and mirrors in the scanner unit first

Where did you see that code?!!!!

switch on the printer while memory counting press 3 then all led will glow stable then press 9 then start button u will find full nvram on display then press 6

HP Laser jet 4345 mfp has 58 04 error HP Enterprise Business Community

58.04 error is an Engine Power Supply error. RM1-1041 is the part number for 110v RM1-1042 is the part number for 220v. You will need a tech to swap it out. You have to strip the printer down to get to the part.

it might be the problem of cartridge drum is not rotating properly pls change the cartridge or change the main motor assembly

hey edmrb. Sorry to hear your having trouble. Try working through this document to see if it helps resolve the issue. A 'Fatal Error' (MSI error) Displays on the Computer During HP Software Installation in Windows Let me know if this helps resolve the issue. If not post back with any new information and we can go from there,

13.31.00 = Media is jammed in the reversing assembly

57.04 indicates the main fan (FN101) is not working. Listen for the fan to operate while the printer is initializing. If the fan does not operate during the initialization sequence, replace it. Part Number: RK2-0278-000CN Fan, Main Cooling

I'm assuming that you're trying to scan to your computer.?? I'm not specifically knowledgeable about the HP M4345 printer.... but, it HAS to have a cable connection. The cable should be one that has a usb connection on one end, and a small kind of rectangular plug on the other that plugs into the back of the printer.. Look on the back of the printer. There has to be a connection, besides the jack for the 110 V.

It may be your ink you need to renew

1 Press MENU.2 Touch CONFIGURE DEVICE.3 Touch I/O.4 Touch EMBEDDED JETDIRECT MENU or EIO JETDIRECT MENU, depending on which type ofnetwork connection you are using.5 Touch TCP/IP.6 Touch CONFIG METHOD, and touch MANUAL.7 Touch MANUAL SETTINGS8 Touch IP ADDRESS9 Touch the left arrow or the right arrow to highlight each segment of the IP address.10 Use the numeric keypad to type the digits in each segment of the IP address.11 Touch OK to save the IP address.

The printer may need a "swing plate" replaced to solve the fuser noise. Remove the fuser and look at the black gear inside the printer on the left side. Do the teeth on that gear look worn ? If so that gear (swing plate) needs to be replaced. Its a hard job to do. Can you turn the fuser gears with it out of the machine without them skipping ? The tray 2 jam may just be worn rollers in tray 2 or a stuck sensor. Good luck !

print single page only, see where it stops. Suspect problem at output end. Check fuser

Check the tray feed rollers

The cartridge isn't being recognized by the printer. Send the cartridge back to the manufacturer.

when powered off the printer, press 3 and 6 and hold, power on, make your choice at menu, (cold reset) and press ok. printer will restart itself.