20 Most Recent Hotpoint JE740WY/GY Microwave Oven - Page 8 Questions & Answers

this sounds like your megertron has burnt out,, best bet is bin it and buy a new one there only £50.00p up now, to fix yours will cost all of that, and dont try fixing it yourself it can kill you, there could well be over 1000 volts inside your unit, tuch that and its a set of wings for you, ok!

HI. The most common issue here will be a failed turn table motor. This motor is located beneath the actual table housing. replace this failed motor.

Note(The uncommon problem area will be a failed relay. although, highly uncommon, this may be the issue. i would advise to inspect the motor control relay located on the main control-board for visible burn marks)

Check your door satey interlock switches.

If these switches fail (do you open the door while the machine is cooking?), the microwave doesnt know the door is shut and will not turn on the magnatron.

If you need more help, let me know.

a

They may not be fixable, depending on the type of buttons used. Many devices use a 'snap dome' switch, which is a little metal disk that 'pops' in and out like an oil can. Problem is, sometimes they get pushed too hard, or just get old, and they stay in the 'popped' position. It is sometimes possible to repair them, often not. A repairman is likely to charge more than the cost of a new one: they'd have to take the thing pretty much apart to get to it, and then may not be able to fix it.

Sorry it's not much help.

You can buy the glass from

http://www.us1internet.net/RVM1325BW02/

You can also try partstore.com

Please make sure to rate this solution

F3 on a GE / Hotpoint microwave means you have a shorted membrane keypad.

So until it is repaired, please leave it unplugged or leave the door open when it's not in use, and please do not leave it running unattended.

On this model, the membrane keypad is not available as a separate part, so you would have to order the control panel frame assembly, which comes with a new keypad.

At our Web site, we have a video available showing how to remove a typical over the range control panel assembly in under 5 minutes.

Then you disconnect the keypad strip as shown in the attached photo.

Next, move your circuit board into the new frame. That is a simple do-it-yourself job.

You can find helpful exploded view diagrams and order parts by entering your full model number here.

The control panel frame assembly with keypad is part number WB07X10874 and you can get it for $75.98 here. (Compare that to $120.75 from GE!)

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

It is very likely that the motor that spins the plate is wearing out. You can find a replacement on ebay and many other sites.

Many thing can do this but, common things are....loose high voltage wire.....poor solder joint on board.....magnetron.....power relay.....

check out the users manual http://www.rgsservices.com/images/appliance/RVM1435WD.pdf that will guide you on how to do that

You can download GE owner's manuals and installation instructions here.

Otherwise, GE Customer Service is here and they can point you to the proper manual.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

If it went dead almost immediately after pressing the Start pad, that's usually a shorted high-voltage capacitor.

If it went dead a few seconds after pressing the Start pad, that's usually a failing high-voltage transformer.

GE / Hotpoint models usually have about a 2-second delay between the time you hit Start and the time the high voltage section turns on.

Here are some links you or someone you know can use for test help, but read their safety warnings first:

http://www.gallawa.com/microtech/cap_test.html
http://www.gallawa.com/microtech/xformer.html

You can usually find helpful exploded view diagrams and order parts by entering your full model number here: http://tinyurl.com/gv383

There should also be a "mini-manual" hidden inside the unit behind the control panel or hidden on the left side behind the grille, which is very helpful when troubleshooting & testing.

We're happy to help and we appreciate your thoughtful rating of our answer.

There may be a fuse either inside the bottom cover or the back cover.

la mia gru hiab 550/6 jib135/4 da errore nello space e 36

I need it too.

We need just a bit more info from you please in order to possibly help you.


Model number of your steamer please. I understand the brand is TEFAL

I could pick one and give you the manual link but I don't think it would be the manual your looking for. Just being honest. Help us help you.

Thanks

Kelly

I am going to give this a shot. There are 4 Tefal steamer manuals here. Hopefully this link has your manual.

http://www.tefal.com/Consumer+service/Use+instructions/Home+Use+Instructions.htm?DdlFamily=%7B0A36B0FA-0D32-4C91-A92C-C08C22E135AD%7D

Microwaves generally last about 2000 hours before losing power. Here are some basics to try: Make sure the power plug is securely plugged into the wall outlet. Listen for an audible click when you close the door. Unplug it, wait 30 seconds, plug it back in (this may reset it). If the start button is then not appearing, there may be a problem with the touchhpad or control panel. Teka's customer service: https://www.teka.com/global/support/

Request the manual directly from Mandine or the supplier.

This is not a North American make. Try the link https://www.google.com/search?q=amstar+1000+dgss+microwave+manual ..

They are usually at the rear where the power lead goes in. This will state the maker, the address, the voltage and watts, the model number and serial number. That is a statutory requirement. In some circumstances they are in the door frame rebate but not so common where heat is involved. https://www.google.com/search?q=galanz+microwave+air+fryer+serial+number+location ..