Hitachi Deskstar 7K250 80GB (hds722580vlat20) 80 GB Hard Drive - Answered Questions & Fixed issues

Since it's an IDE hard disk, you'll have to setup disk jumpers, please check the following image:
If you want more information please see the installation guide at the following link:
http://www.hitachigst.com/tech/techlib.nsf/techdocs/4DD4DCCA11DE5EB186256D6A0061C8A8/$file/Installposter.pdf

you can find it from this manuel....

http://www.hitachigst.com/tech/techlib.nsf/techdocs/B272B6575A7B410886256CE90058095B/$file/D7k250_ps1.pdf

Press either delete or f2 during the boot up process to enter BIOS scroll down to set user password you can change or remove your password from there
good luck

You won't loose your data Why wold you think you would? once data is written to a hard drive it remains there until it is removed be a user, it works on the same principlea a floppy, the magnetic coating on the surface of the anodized disks inside of the HD are written to and retain memory of the data, the only things in a computer that won't keep their data are the RAM chips which need electricity running through them to work.

there are few thing you ahve to keep in mind

there are two type of hard disk
1. IDE
2. SATA

As per your hdd capacity it should of IDE type.

Now there are two IDE slots on motherboard. One is Primary and other is Secondary

You can fix two hdd with one IDE Slot that mean you can fix up upto faour IDE hdd at a time

Now again there are Primary master and Primary Slave

and

Secondary Master and Secondary Slave

Now You have to examine what was the location of previous hdd
1 Primary Master
2 Primary Slave
3 Secondary Master
4 Secondary Slave.

Now you have to make a HDD master or Slave.

just in between data cable connector and power cable connector there is a jumper. that specify the master or slave. do reply me if it works well thanks

We call them in the industry Death Stars! I have had several just die on me! If the drive does not show in the BIOS then you can't do a low level format! All the ones that have died on me have burnt out components on there circuit boards. Way to small for me to solder! So they were thrown away!

Update your ms Drivers and Service pack.

Found this,,,,, https://www.justanswer.co.uk/consumer-electronics/c5uh2-hitachi-xl500-won-t-connect-hear-running-no-light.html hope it helps.

use this? it can backup anything. https://www.2brightsparks.com/download-syncbackfree.html

You will have to use the HDMI port on the mac. provided you have a HDMI input in the projector

BENJAMIN, Your message does not qualify as a question or query for a problem, try somewhere else DO NOT MAKE THIS SITE WITH YOUR GARBAGE Take your GARBAGE to another Side Your message qualifies as SPAM

buried in endless spam are you. does it fail on 2nd PC???????????????????????????? but yes, I am the MVP of external HDD< I build my own. Have over 5 here for Backups . lots of causes, for sure bad drive, or missing drivers.. bad HW hardware or BAD software SW. Missing 12vdc 2amp power pack>, lost or using wrong one. when pack above does the HDD spin? usb connected to PC. NO PC stated, NO OS stated, windows/chrome/Linux/android? its at lease 10 years old , see posts back that far. not good old HDD,this old. sold during W7 era. 2009. The drive has 3.5" HDD that needs lots of power (Amps) to start up that big motor inside, and is first thing to learn . 2amps it needs, ok? so if pack is missing it will never startup on any USB port, not rated for 20x standard USB load factors. some laptops only do 0.1amps (100mA) and are useless to startup any hdd motor of any kind. see why here. and see a better extremal solution cheap.! $10 http://www.pcdied.com/external-hdd.html

Tried googling for the answer but couldn't find it. Try calling an it support company, I'm sure they'll help you out for free. Perhaps you can try https://www.computersinthecity.co.uk/, they have been helpful to me in the past.

No. http://www.hitachidigitalmedia.com/en-gb/discontinued-products/plasma-tvs/42-106cm/42pd7200

Hi, What is the router/modem model number? Have you tried a different cable? Have you gone into the menu, networking and setup ?

try downlolading the driver compatible with win 10 os

Try to right click the listing. you should get a dropdown where you can repair of reinstall the drivers

Maybe this will work for you. https://ibm-hitachi-drive-fitness-test.en.softonic.com/

purchase a Roku box

See if it supports chrome or firefox then install either then try it.