Jack Lalanne s Pro Stainless Steel Power Juicer - Page 3 - Answered Questions & Fixed issues
Apt type no imm 24 tiime clock connected to a central heating oil boiler, earth terminal
Based on the information you provided, it would be like describing an electrical cover or box with some wiring harness. It is important to note that working with an electrical system requires caution and knowledge of electrical safety practices. If you are unfamiliar with electrical work, it is best to seek the help of an electrician to avoid potential hazards. Having said that, if you're looking for the end of the earth, it's usually indicated by a landmark (square with a horizontal line) or the letter "E". There is one that helps with surge protection and proper grounding of electrical appliances.
8/3/2023 8:09:04 PM •
Hardware &...
•
Answered
on Aug 03, 2023
•
36 views
Aqua plus timer turns on filter, but will not turn it off. Filter works on and off manually
If your Aqua Plus timer is successfully turning on the filter but is not turning it off automatically, there could be a few potential causes for this issue:
- Timer Programming: Double-check the programming of the Aqua Plus timer to ensure that the off time for the filter is correctly set. Verify that the timer is configured to turn off the filter at the desired time. Review the user manual for the Aqua Plus timer or consult the manufacturer's website for detailed instructions on how to properly program the timer.
- Timer Power Supply: Check the power supply to the Aqua Plus timer. Ensure that it is receiving a consistent and uninterrupted power source. Any power disruptions or fluctuations can affect the timer's functionality. Confirm that the timer is properly connected to the power source and that there are no loose or damaged connections.
- Defective Timer: It's possible that the Aqua Plus timer itself is faulty. If all the programming and connections seem correct, but the timer still fails to turn off the filter, it may require replacement. Consider contacting the manufacturer's customer support or consulting a pool professional for further assistance or potential warranty coverage.
- Manual Override Switch: Some timers have a manual override switch or button that allows you to manually turn the filter on or off regardless of the timer settings. Ensure that this switch is not inadvertently set to the "On" position, as it would override the timer's control.
If you have exhausted these troubleshooting steps and the issue persists, it is recommended to reach out to the manufacturer's customer support or consult a professional pool technician. They can provide further guidance and assistance in diagnosing and resolving the issue with your Aqua Plus timer.
7/15/2023 1:45:05 PM •
Hardware &...
•
Answered
on Jul 15, 2023
•
56 views
How to repair a Defiant Motion Security Light.
try this
turn on the light at night
if it doesn't turn off after say 5 minutes (you should be able to set the stay on time)
switch off and back on
for most security light operations that action places it in the watch mode
the light will come on immediately but will go off after the set time period
from then on any intruder movement should set it on fort the set period of time
3/27/2023 8:15:33 PM •
Hardware &...
•
Answered
on Mar 27, 2023
•
5,201 views
I have my ej500 set to turn on at sunset and off at sunup. however it turns off at 11 pm. How do I fix this?
The first thing you should check is that the time and location settings on your ej500 are correct. If they are incorrect, the timer may be turning off at the wrong time. Here's how to check:
- Press and hold the "clock" button on your ej500 timer for about 3 seconds until the display flashes.
- Use the "+" and "-" buttons to set the current time, making sure to set the correct AM/PM designation.
- Press the "clock" button again to confirm the time setting.
- Press and hold the "mode" button until the display shows "LAT" for latitude and "LON" for longitude.
- Use the "+" and "-" buttons to set your location's latitude and longitude. You can find this information by doing an internet search for your city's coordinates.
- Press the "mode" button again to confirm the location setting.
Once you have confirmed that the time and location settings are correct, try resetting the timer to its default settings by pressing and holding the "reset" button on the side of the device for about 3 seconds until the display flashes. Then, reprogram the timer to turn on at sunset and off at sunrise. Here's how to do that:
- Press the "prog" button on your ej500 timer.
- Use the "+" and "-" buttons to set the "on" time to "sunset" and the "off" time to "sunrise."
- Press the "prog" button again to confirm the programming.
If the timer still turns off at 11 pm instead of sunrise, it's possible that there is a malfunction with the device. In that case, you may need to contact the manufacturer for further assistance or consider purchasing a new timer.
3/9/2023 3:42:38 PM •
Hardware &...
•
Answered
on Mar 09, 2023
•
72 views
I need an instruction mannual for the le saucier with the automatic dial
Le Saucier is a kitchen appliance that is used to make fresh butter and other creamy sauces. Without knowing the specific model of Le Saucier you have, it is difficult for me to provide an instruction manual for the automatic dial. However, here are some general instructions on how to use the Le Saucier:
- Assemble the Le Saucier according to the manufacturer's instructions. Typically, this involves attaching the paddle and placing the machine on a flat surface.
- Pour the cream into the Le Saucier. The amount of cream needed will vary depending on the size of the machine and the recipe you are following.
- Set the machine to the desired speed and let it run. The automatic dial may allow you to set a specific speed or program, depending on the model.
- After a few minutes, the cream will thicken and eventually turn into butter. Once the butter has formed, stop the machine and drain off any excess liquid.
- Use a butter churn or cheese cloth to remove any remaining liquid and shape the butter into a desired form.
If you are still having trouble with your Le Saucier or need a specific instruction manual, I recommend contacting the manufacturer or searching online for a downloadable manual.
3/9/2023 3:05:57 PM •
Hardware &...
•
Answered
on Mar 09, 2023
•
84 views
Do you know where I can find a timer for a Westpoint DQP 12 set 9011
I'm sorry, but as an AI language model, I don't have access to information on specific product manuals or instructions. However, I can provide you with some general troubleshooting steps for a timer that is not working properly.
- Check the power source: Make sure the timer is properly plugged in or has a fresh battery if it's a battery-operated device.
- Check the settings: Verify that you have correctly set the timer for the designated time and that it is in the correct mode of operation.
- Reset the timer: If the timer is not working as intended, try resetting it to its default settings.
- Clean the timer: Dust and debris can affect the timer's functioning, so make sure to clean it thoroughly.
- Seek professional help: If none of the above steps work, it may be time to seek professional help or replace the timer.
If you are still having trouble finding a timer specifically for your Westpoint DQP 12 set 9011, I would recommend reaching out to the manufacturer or a professional technician for further assistance.
3/3/2023 5:08:17 AM •
Hardware &...
•
Answered
on Mar 03, 2023
•
35 views
AMF Paragon TI Mite Timer - Model PLTI-O. How do you set the timer on it please?
Question edited for a lot more clarity.
Question moved from Office Equipment to Timers.
This timer has a fixed setting for turning on lights or appliances. To set the time, turn the small dial marked '8765' (which represent the hour when the lights will turn ON, so that the time you wish them to come on is next to the current time. In other words, if the current time is 6:00pm, and you want to have the lights come on at 8:00pm, set the 8 on the small dial next to the 6:00pm on the timer body, and plug everything in.
..
3/1/2023 7:21:52 PM •
Hardware &...
•
Answered
on Mar 01, 2023
•
94 views
Not finding what you are looking for?