Euro-Pro 9105 Computerized Sewing Machine - Answered Questions & Fixed issues

needle hook timing is set when the needle in the full down position has the bobbing carrier hook approaching the needle AS the needle starts to rise the hook is at or just about at the eye of the needle The adjustment is on the needle cam lever at the end of the machine and on most , there is a clamp around the shaft that is loosened of , the clamp tapped up or down to achieve the correct setting and re-clamped

contact shark

Hi could you explain, what you mean by the machine jams up.\ Best wishes

Need more info.

Has the clutch been disengaged to wind the bobbin? Pulling straight out on the handwheel on some machines will stop the needle from moving so that a bobbin can be attached and wound. If this is the case you simply push it straight back in. Also, on a computerized or electronic machine if the bobbin winding post is pushed right, the clutch will disengage. --Push it all the way left when you are done winding the bobbin to re-engage the clutch. If the problem is internal, like a slipped belt, you will need to have someone open up the machine to repair it. Hope you get it going again!

New needle, right way around, and thread again from scratch, manual in hand. Make sure you're threading with the presser foot up. Raise the bobbin thread. Start each and every seam thus: 1. Place the work under the needle. Use the handwheel or needle up/down function to drop the needle into the fabric. 2. Drop the presser foot. 3. Hold the bobbin and top thread ends together and take about 3 stitches. 4. Drop the thread ends and sew normally. See also: http://www.picturetrail.com/sfx/album/view/22521551 last pair of photos.

Sounds like you need to loosen the tension.

try this link and see if it's the right onehttp://www.sewusa.com/Sewing_Machine_Manuals/Euro_Pro_Sewing_Machines/Euro_Pro_9105_Instruction_Manual.htm

here is a link for part for the machinehttp://www.sewingpartsonline.com/europro_9105_sewing_machine_parts.aspx

try oiling the machine

http://www.tradebit.com/filedetail.php/9338637-euro-pro-9105-sewing-machine-manual

Enter your model number here - http://www.euro-pro.com/europro/default.aspx for a download

here is a link for a manual, it should have the information youneedhttp://www.sewusa.com/Sewing_Machine_Manuals/Euro_Pro_Sewing_Machines/Euro_Pro_9105_Instruction_Manual.htm

I had the same problem ! I had to take it to be repaired, they had to take it apart & grease the whole thing, I hadn't used the machine in a couple of years & the original "grease" became too hard for the foot to come down.

Good morningI will give you the same advice as I gave here a minute ago.Go to the yellow pages or on line and find an authorized dealer for your machine in your area. Take contact and ask for the correct bulbs be sent to you.enjoy your coffeekolbrun

Manufacturer's site: http://www.sharkclean.com/manual/9105_REV_0902.pdf

check with these sites

sewingpartsonline.com

whitesewingcenter.com

sewingpartsdirect.com

sewingsupplieswarehouse.com

sewforless.com

sewvacdoctor.com

check with these two websites

sewingpartsonline.com

sewvacdoctor.com

As far as the power cord, you can ask for it as "figure of eight power cord". At the other end it will have a plug suitable for your local electricity. Here is a link for buinig this cable on line.
As far as the user manual, follow this link, and at the new window click at "click here to start download from Mediafire..." like the screen bellow:

Save the manual at any place at your computer because it's not easy to locate it at the net.

In case of a problem or clarification or further details needed, don't hesitate to post me a reply before rejecting my answer.
If you are satisfied, accept my solution.

Thanks and regards
Stelios
direct FixYa link: http://www.fixya.com/users/technical114

Sears PartsDirect has manufacturer-approved replacement parts and accessories for Euro-Pro sewing machines.