20 Most Recent Remote Start System - Page 2 Questions & Answers

Avital and viper remotes even though they look the same, they operate at different freqs. Im a retired alarm installer i could never get them to interchange.

Did you connect the tach wire of the unit to your car? if not you need to refer to your documentation to turn on or off the tachless operation for the unit to work correctly.

problem is the low battery have it load tested and charged up or replaced remote or key still use the same bad battery

Lock the driver side door then open it with key that might reset you anti thief to your remote.

Consider how the switch will be used before choosing a mounting location. Check for rear clearance before drilling a 9/32-inch hole and mounting the switch.The GRAY wire in the two-pin plug may also be used as a (+) ghost switch input and can be connected to any (+) switch in the vehicle. (See Feature Descriptions section of this guide.) This is from the installation manual for the Viper 300. To answer your question, it is probably camoflaged. They only needed to tie +12vdc to the input line. What does this mean? Well, my best guess is, they are using one of your switches on your dash to act as the Valet function. Look for where the Gray wire, from the wiring harness of the Viper goes to: that WILL BE your hidden Valet switch. Best of luck! Viper 300 ESP Installation Manual Plug in Harnesses Super Bright Led Valet...

here's the manual https://www.directeddealers.com/manuals/OG/Viper/G4806V%202013-06%20web2.pdf

It says its a Viper alarm system. . If the alarm system is active, reprogramming the ignition keys was a waste of money. The problem is in the control box for the viper alarm system. It has disabled the ignition because it thinks that is being broken into. there are sensors that monitor the the vehicles vibration and is probably a problem with one of the sensors or maybe even the control box itself.

You need to re-program the TACH wire.. open the door start the car with the key, between 5 seconds press the valet switch 1 time and press it again and hold it until the led flashes and the car will beep and then turn it off and start the car with the remote and it should be programed now. if that doesn't work take it to a authorized viper dealer to have it fixed.

son muchos cables los ke tienes ke unir asi es ke te recomiendo ke lo lleves a aun lugar dodnde hagan instalaciones te va salir mas barato pagar para ke te lo intalen ke cometer un error y tener ke pagar para repararla

hi no your car alarm wont effect the tire pressure but if you have no problem with your car alarm its not your car alarm causing the problems its the dealer not wanting to honor the warranty by making up excuses if your car is covered by the warranty they sold you the car with alarm already installed so they are still liable i guarantee that warranty never said not covered by the warranty because of an after market car alarm installed take the car back and order them to fix the problems because its under warranty and they sold you the car with the car alarm so thats there problem not yours Take a male friend with you if you feel abit over whelmed as they try to take advantage of everyone and he can speak on your behalf and offer you supportcheers

There can be problems when iOS is upgraded. Get the latest version with the latest bug fixes. Watch the Viper app for version changes and download it when it gets updated. Check the Viper support web site: http://www.viper.com/Support/

put the radio fuse from the fuse box and reinstall it

Same as the 5706v. Here is a current link for the quick install guide. http://www.net-import.dk/images/viper%205606v%20installationsmanual.pdf Also 5706v install guide available at "the12volt.com in the downloads section need to be registered to download.

I need to know what make, model and year vehicle you have to help you with this. The newer the vehicle, the less likely you will be able to install it yourself.

It sounds like a problem in the remote start module that was installed. I assume it has not always done this. See what type of warrenty you have on it. Probably none but sometimes suprises happen.

On some remote starters, there is print on the back of the remote starter itself. It is hard to see with it being black raised text on a black box. If not there, sorry DEI Viper is pretty protective on their installation manuals.

if it cranks and wont start then its probably the bypass the module thats not working correctly

Hello my name is Israel and I will be able to help you. First I will need for you to look for the alarm unit. The model you are giving me is for the remote not the alarm. Once you have this information, let me know and I will send you the instructions for programing the remote to the unit.

start the vehicle. press the valet button and release to relearn tach signal

if the radio powers up during remote start depends on wether or not the appropriate accesorry circuit is being supplied 12 volts from remote start