Kymco Venox 250 - Answered Questions & Fixed Issues - Page 8

Alan, You may have to remove rear fairing to access. Link to forum gives a good guide on how to remove tail light. Check the attached links,instruction and guides, Good luck "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info." http://www.kymcoforum.com/index.php?topic=3077.0 KYMCO AGILITY 125 Service Manual Page 181

Hello P Smurf, Well... don't feel bad...!! The KIMCO drawing is TRASH (in my humble opinion). Just start the engine! - ignition switch on (powers on CDI module) - short B+ 12V to "S" lead (small terminal on solenoid switch = cranking motor (until it starts (or within reason... do not burn out starter)). Really... you can short BATTERY to the starter solenoid... as long as you have the ignition on... It SHOULD RUN (if it can). You only have the REAL two issues you need to start... Fire & fuel... (everything else is mere confusion). IGNORE IT ALL... until you get the engine started...!! I've been reading schematics, circuit drawings, operational diagrams... All of it for more than my adult life... (mere seconds away from 70) amateur radio, patent holder & highly skilled professional... (into full spectrum optics).... I pulled up the appropriate Kymco "drawing"... and while I'll say it is very pretty (colorful) it is also TOTALLY USELESS...!! (top reference below... avoid it!). Whom-so-ever (clown who posted it) that put it together didn't (still doesn't) know their posterior from 75 cents (six bits). I can't even tell if the generator & starter are one-in-the-same (which would be the first place you want to go... Useable VERSION immediately below... Quite Useless: http://www.enmoto.com/enmotoonline/downloads/Specifications/Kymco/Schaltplaene/Quannon.pdf I found another source... that has the COMPLETE information: http://binatani.com/wp-content/uploads/2013/02/wiring-diagram-Kymco-Super8-125cc-engine.jpg http://binatani.com/wp-content/uploads/2013/02/wiring-diagram-Kymco-Super8-125cc-engine.jpg If you don't have a spark tester just have a friend pull the HIGH-VOLTAGE wire loose enough to see the spark jump... Else find the CDI Module/Coil... & replace it (better to get a SPARK test tool...)... I'm just saying Comment me back... every tractor & tiller in the world has the same starter circuit (some just have points & coils in lieu of CDI Modules). I'll be here!!

You probably need a new clutch. That can explain why it bogs. The smoke I don't know.

This is almost always a bad earth or corroded switch. First clean the two terminals on top of the horn. If that doesn't work, take the switchgear with the horn button off your bike and clean inside where the button touches the metal contact. If it's very corroded you might need to source a good second hand unit.

Does bike sound as though.it is trying to crank. If so what sounds do u here. ie. Click. Starter motor turning over. If clicking sound problem lies after the relay. If starter is turning then you are getting no spark. If you are getting nothing at all then it is a safety switch as previously noted

Haynes is the information resource for the DIY enthusiast Online Motorcycle Repair Manuals Cyclepedia Repair Library Free Automotive resources Wheel fitments and Motorcycle Service and... Motorcycle Service and Repair Manuals

Spray starter fluid into the carb with air filter off.

My scooter has no spark how to fix. gy6 chinese ... - YouTube

? 2:29 https://www.youtube.com/watch?v=UU4S0Ov9q4c Aug 24, 2012 - Uploaded by Rolling Wrench Purchase our "NO SPARK KIT" click the link below: ... My scooter has no spark how to fix. gy6 chinese scooter 139qmb qmb13950cc 150cc.

Author Topic: people 50 2 stroke no spark CDI?? - KymcoForum.com

www.kymcoforum.com > Scooters - 50cc > People 50 Aug 5, 2012 - 7 posts - ‎4 authors I have a 2001 people 50 2 stroke that only has 125 original miles. ... I ordered a CDI and coil from monster parts and it still would not start . Author Topic: (Almost) no spark / engine not ... 15 posts Aug 15, 2011 Kymco People 50 - Not A Morning Scooter ... 15 posts Sep 28, 2010 Author Topic: 2005 People 50 2T Mods ... 15 posts Jul 27, 2010 Kymco People 50 - KymcoForum.com 10 posts Nov 15, 2008 More results from www.kymcoforum.com

My bike (different model) had a similar problem. I wiggled the wires all around the starter relay and the panel came live but went off again. A quick rewire and hey presto! May work for you.

check for a damaged micro switch for the stand unit

HI Luann: I'd pull the spark plug(s) and clean and dry them, then check for spark. It's possible they got wet with fuel when the start with kill switch on was tried.

fit in a helical, and keep in the same bolt, that should solve your problem

Kymco Super 9 - Wikipedia, the free encyclopedia

https://en.wikipedia.org/wiki/Kymco_Super_9 WikipediaThe Super 9 is a lightweight scooter made by Kymco. It has modern ... When it failed to meet U.S. emissions regulations in 2008 it was replaced by the Super 8.

KYMCO Agility 50 Scooter Online Service Manual ...

https://www.cyclepedia.com/...manuals/kymco...scooter...repair-manuals/... The CYCLEPEDIA PRESS LLC KYMCO Agility 50 Scooter online service manualfeatures detailed, full-color photographs and wiring diagrams, complete ...

How to replace Stater on 50cc scooter

Hi,try undoing the battery and leave for 30mins and reconnecting the battery and see if it rights itself,worth a try.

bad switch in handle