Tappet clearances What are the tappet clearances for a 1999 model Hyundai Lantra

The valve clearance specification for a 1998 Hyundai H100 2.6 diesel bakkie is:
Intake valve clearance: 0.25 - 0.35 mm (0.010 - 0.014 in) Exhaust valve clearance: 0.45 - 0.55 mm (0.018 - 0.022 in)
The tappet setting for this engine will depend on the specific valve clearance measurements for each valve. If the valve clearances are found to be outside of the specification, the tappet settings will need to be adjusted accordingly. It is recommended to refer to the manufacturer's service manual for detailed instructions on how to perform the adjustment procedure.

large trucks.
D4xx diesels engines used x4 some turbo and not.
its 4 engines not 1, and maker has an EM# engine manual on each

16valves, 4cylindes. SOHC about 4Liters

6.5KG ,MGVW
SO BUY the service manual
or google D4 specs?
i read you D4, service book and it has no such thing at ALL
it uses HLA tappets. hydraulic lash adjusters
so let may guess they make noise and is why the hunt started.
end another fake hunt to nowhere.
page 35


D4AL, AF, DC, AND DB-D, 4 ENGINES,

Question edited for clarity.
Question moved from 'Misc'.

There are two types of valve tappet adjustments. Generic information only because 1.4 Utility isn't a model name or designation.

https://www.google.com/search?q=2010+Opel+Vauxhall+1.4+utility.+How+to+adjust+tappet+clearance

The valve tappet clearance for the Mazda Bongo Brawny can vary depending on the specific engine model and year. Here are some general specifications for the different engine types: 2.0L FE engine: Intake valve clearance - 0.18-0.22mm, Exhaust valve clearance - 0.28-0.32mm 2.5L WL engine: Intake valve clearance - 0.20-0.25mm, Exhaust valve clearance - 0.30-0.35mm 2.5L RF engine: Intake valve clearance - 0.20-0.25mm, Exhaust valve clearance - 0.30-0.35mm It's important to note that the valve tappet clearance should be checked and adjusted by a qualified mechanic using the correct specifications and tools. Incorrect adjustment can cause engine damage and poor performance.

Try setting the valve clearance on your 1999 2.7 Nissan Hardboy diesel to 0.14 inches on the intake and exhaust sides.

The tappet clearance for your Hyundai Atos 2007 would be:
• Valve clearance Warm: 0.2 mm intake, 0.25 mm exhaust.
• Valve clearance Cold: 0.1 mm intake, 0.17 mm exhaust.

See if this helps. It's for the 1Liter -
Service Manual2006 Matiz 1 0L SOHC ENGINE MECHANICAL

When setting tappets, it has to be born inind that the valve stem wears an indentation into the face of the rocker. This prevents a really accurate tappet adjustment, so the customer is right again. If you do not posess a tappet setting dial gauge, a normal engineers dial gauge will do just as well. The procedure is the same as using your feeler gauge except that you set the dial gauge up on the cylinder head with the pointer resting on the head of the rocker. Press down fairly firmly on the rocker valve end and zero the gauge. Next lift up on the rocker and read off the clearance, from the gauge, Use a magnetic base to support your gauge and repeat the pocedure for each valve pair.

you will find two bright links on the chain that correspond to the dots on the cam shaft and the key ways on both cams should line up with the top of the head facing back towards the firewall IE parallel with the top surface of the head ( where the tappet cover bolts on), with the crank on TDC (top dead center)

On the intake 0.0008 or 0.0020 (it's in between these 2)

this is for the stem to guide clearance. (for the intake)

The Exhaust 0.0018 to 0.0030 stem to guide clearance.