20 Most Recent 1997 Ford F250 SuperCab Questions & Answers


I think your right, CV joint

1997 Ford F250... | Answered on Sep 29, 2018


fuel pressure should be 35 - 45 psi.could have faulty tps sensor.could have intake vacuum leak or ignition timing valve timing off due to worn timing chain.do engine vacuum test replace all vacuum hoses bad leaking egr valve diaphram or gasket will cause engine run poorly.

1997 Ford F250... | Answered on Sep 01, 2018


Time for a GOOD SIZE trans cooler!

1997 Ford F250... | Answered on Mar 13, 2018


air in the pump and injector lines
bleed the air out of the pump and loosen the injector line nuts to bleed the injectors

check for problem furl line , filter seals , pick up line in the tank, and tank not venting properly

1997 Ford F250... | Answered on Nov 24, 2017


run the fault codes
indicates that the ambient temp sensor or BARO sensor are not working and reporting to the ECM so that the correct air/fuel mixture can be set for starting

1997 Ford F250... | Answered on Nov 19, 2017


There will be a code in memory which will indicate the problem. From you saying it flashes at cruise it is most likely your torque converter is not locking up as it should.

1997 Ford F250... | Answered on Nov 16, 2017


Hello,

If your low beams work it's not the multi-function switch located on your steering column (two bolts and a plug). If you unplug the abs sensor on the rear differential and the ABS stays on and your blinkers work and you don't blow fuses could be the sensor. However, if this is not it you may have a ground problem (micro-friction). Usually these two systems are not connected and these may be completely different issues.
Possible Scenario: aftermarket stereo installed incorrectly.
Scenario Two: both of these sytems have bare wires and touch every so often causing your grounding problem. (There is a fuse-vibration testing technique that can be used to find the bare-wire(s))
Try to fix the blinker problem first you may find the ABS problem along the way (common wires of Blinker/ABS bundled together.
Trace and inspect.

Hope this helps--

1997 Ford F250... | Answered on Jun 07, 2017


On this website you find fuse box diagram and description for Ford E250

Ford Series 250 E250 1995 2014 fuse box diagram Auto Genius

1997 Ford F250... | Answered on Apr 14, 2017


check and make sure push rod didnt damage head,rocker , valve or lifter [which i would replace]if all looks good clean repair and replace

1997 Ford F250... | Answered on Jul 10, 2016


there is a code in the TCM that needs to be checked out.

1997 Ford F250... | Answered on Aug 27, 2015


Think it's on top of the transmission near the rear. Real pain to reach and service.

1997 Ford F250... | Answered on May 24, 2015


I drove truck for 30 years, and I used the trans fluid in diesel fuel to help keep injectors clean! Just be sure not to use too much! I would only use a 1/4 of a quart per tank full.

1997 Ford F250... | Answered on Apr 04, 2015


Usually need a 1/2" drive placed into tensioner pulley and ease it back till you can remove the belt off it. Then the belt will slide out so you don't have to remove anything. Follow the reverse order to put back on and follow the diagram under hood usually in plain view if you forget. It can be somewhat a puzzle depending on how many pulleys it needs to wrap around... You will not need to remove anything if you do it right. Also buy the 3 year plus one since the other needs to be replaced yearly...

1997 Ford F250... | Answered on Apr 01, 2015


You just gotta face it: your engine is munched.

Sorry.

Nothing but nothing will totally ruin an engine faster, or more thoroughly, than overheating. And the damage that is done it not the kind that can usually be repaired. Every component of the engine is likely ruined, every single internal part.

If you would have turned the engine IMMEDIATELY off, and coasted to the side of the road, you might not be in this position. But since you ran it until it started pounding ("pinging" you called it), you can rest assured that it will likely never run again.

Sorry!

1997 Ford F250... | Answered on Mar 19, 2015


I would start by checking you switch for the tanks to make sure it is working right and if the front tanks fuel pump does not work after you check the switch I would get a 12 volt electrical test light and see if your getting power to the front fuel pump if your getting power to it I would say you have a bad pump . But some times the pump will run but the diaphragm gets weak in them.

1997 Ford F250... | Answered on Mar 12, 2015


Sounds like a failing or dirty switch. I had a car that did that and it turned out that the wiring harness connection to the switch housing had worked loose making a partial connection.

1997 Ford F250... | Answered on Mar 05, 2015


More than likely it will be your switch for the power windows

1997 Ford F250... | Answered on Mar 04, 2015

Not finding what you are looking for?
1997 Ford F250 SuperCab Logo

580 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

F-250 Ford

  • F-250 Ford

Most Popular Question

ford f250 7 3 diesel engine good idea

  • Cars & Trucks
Loading...