20 Most Recent 1994 Dodge Ram 2500 Questions & Answers


No external fuel filter. Only the dock in the fuel pump in tank. A lot was available to install an external but location would be on the frame rail if present and sit was a dealer add-on that was very uncommon.

1994 Dodge Ram... | Answered on Mar 13, 2019


Your question says Dec 2018 so I don't know if you've had it repaired yet but I'd like to help. The 4x4 in your truck is not electronic but it has a light to tell you when it is engaged. Assuming the transfer case lever feels like it shifts okay when you go from 2wd-hi to 4wd hi, what you want to do is, 1)put the vehicle in park, leave truck in 2wd, key on engine off and parking brake on if it works. 2) Crawl under the truck from the passenger side and look at the front axle from the middle of the truck. There is a square, aluminum piece mounted to the axle with 2 vacuum lines going to it and an electrical connector hooked to it. 3) Unplug the electrical connector and jumper the 2 wires inside the harness while someone looks at your 4x4 light on the dash. The light should turn on. If it does then either the vacuum lines are rusted, plugged, unhooked, or the vacuum canister on the axle is bad.(Both are common) To test the vacuum canister you must have a vacuum hand pump tester or start the engine and feel the vacuum lines. One of them should have good suction at idle. They are bonded together but you can use the one with good vacuum by pushing it onto each vacuum nipple, one at a time to see if the axle engages. Remember to plug the electrical connector back in so you can see if the light comes on. That vacuum canister engages a slide lock to hook the inner axle to the outer axle. To see if it's working just jack the right front tire a couple inches off the ground and try to spin the tire. When it engages the front driveshaft will start to spin from spinning the tire. The truck being in 2wd and in park will stay put. DON"T LET ANYONE PUT IT IN GEAR WHILE YOU ARE UNDER IT!!! They also sell electronic axle actuator kits to eliminate the vacuum issue
Hope this helps.

1994 Dodge Ram... | Answered on Mar 01, 2019


Sound like your fob and your pcm are not communicating with each other.try the other key see what happens.

1994 Dodge Ram... | Answered on Dec 06, 2017


while its running try wiggling the pcm wires one by one. if it stalls theres your answer

1994 Dodge Ram... | Answered on Oct 22, 2017


WENT YOU BOLT IT UP IT' GROUNDED.

1994 Dodge Ram... | Answered on Oct 12, 2016


If you are talking about the blower motor, have you checked the high speed blower relay ?

1994 Dodge Ram... | Answered on Feb 28, 2016


Replace the blower relay. Sorry I can't tell where it is located. # locations I know of are the fuse panel, on the firewall or fender well. I can always find them, I just work on to many different vehicles. These relays have 5 pins on them.

1994 Dodge Ram... | Answered on Feb 27, 2016


You have to knock out the tire bolts to separate them.

1994 Dodge Ram... | Answered on Jan 11, 2015

Not finding what you are looking for?
Cars & Trucks Logo

Popular Tags

158 questions posted

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ram 2500 Dodge

  • Ram 2500 Dodge

Most Popular Question

c not blow air high all other positions

  • Cars & Trucks
Loading...