Konica Minolta bizhub - Recent Questions, Troubleshooting & Support - Page 7


my machine konica minolta C252 is giving the code 9401 how should I resolve and what is

Konica Minolta... | Answered on Nov 29, 2018


Must be Second network selected,
in system 2 disable that

Konica Minolta... | Answered on Nov 25, 2018


I want to see Print test page.

Konica Minolta... | Answered on Nov 19, 2018


Sounds like a drum motor is going bad. The extra resistance from the thicker paper may be exposing a weakness in one of the drum motors. They aren't terribly expensive but figuring out which one it is might be troublesome on top of the removal and instillation process.

Konica Minolta... | Answered on Nov 09, 2018


13DD is an eeprom error. Make sure the prcb is connected properly and that the eeprom is installed. If problem persists you may need to replace the prcb.

Konica Minolta... | Answered on Nov 09, 2018


Description

The leading edge of paper is not turned ON (unblocked) the paper exit sensor (PS3) since the paper feeding is started.

Causes

• Transport motor (M1) • Fusing motor (M3) • Registration clutch (CL4) • Registration sensor (PS1) • Paper exit sensor (PS3) • Front side board (FRB) • MFP board (MFPB)

Konica Minolta... | Answered on Nov 09, 2018


The registration roller is not causing the print sync issues. It is the sync clutch on the right side of the transfer assembly that is located in the right door that folds down. It is easily replaced and can be found in numerous places online.

Konica Minolta... | Answered on Nov 09, 2018


1 Check the connection of the fusing unit. 2 Check the fusing unit, IHC, IHPU and PRCB for proper connection and correct or change as necessary. 3 Replace IHC 4 Replace IHPU 5 Replace PRCB

Turn machine on holding down the utility key.Trouble reset and Turn off machine.Good luck.

Konica Minolta... | Answered on Nov 09, 2018


1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.). 4 Change imaging unit. 5 Change PRCB

If you do not use the original toner. May cause problems.
Make sure you only copy red in order for the red to be normal.
When the machine displays the code, you open and close the front bezel and retry until the code is not displayed.

Konica Minolta... | Answered on Nov 09, 2018


Am having little Challenge if I send job to printer Bizhub c451. D job will enter printer and it will wrote System Printing and it will not print
10_23_2018_7_09_39_pm.jpg

Konica Minolta... | Answered on Oct 23, 2018


Could not find the code in the service manual

Konica Minolta... | Answered on Oct 21, 2018


Replace the transfer belt and roller and clean the sensor under neath the transfer belt

Konica Minolta... | Answered on Oct 21, 2018


Sir/Mam,
On the right side of the machine just below the scanner section (The part with the big glass) is a cover next to where you connect the Ethernet cable. Remove the cover, with the machine on use a small screw driver and gently depress the small black switch. The machine is going to go thru some screens when you see the screen with the copiers on it to the left on the screen in the middle you will see a "." when that is displayed press 3. The code will come back but now press the Utility/Counter button, you should see a button that says Maintenance Mode press that, see Trouble Reset press that and the machine will again will go thru warm up procedure, you will see the "." DO Nothing! The machine should go to "Ready to Copy" if the code comes back. Have a technician look at it DO NOT CONTINUE TO RESET the code is for the Hot Part called the FUSER. It can catch on fire! And that will ruin a perfectly good day!!!!

Konica Minolta... | Answered on Oct 20, 2018


Has the transfer belt and transfer roller been replaced?

Konica Minolta... | Answered on Oct 20, 2018


WARNING: DO NOT CONTINUE TO RESET the code is for the Hot Part called the FUSER. It can catch on fire! And that will ruin a perfectly good day!!!!


Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.

Konica Minolta... | Answered on Oct 20, 2018

Not finding what you are looking for?

-490 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6872 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

carpediemweb

Level 1 Expert

51 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Konica Minolta Office Equipment & Supplies

  • Forum

View Most Popular

  • Konica Minolta Office Equipment & Supplies
Loading...