20 Most Recent Pride Jazzy Select 6 Indoor Power Wheelchair - Page 2 Questions & Answers

If your charger has a red and a green led on it when the green led lights the battery is charged. If you use it a lot during the day it may take 8 to 10 hrs or more to fully charge the batteries

Go to Pride's website and download the service manual. It's in there

Until the green light o the charger comes on or the charge meter shows one amp or less. If the batteries were drawn down too far the 5 amp charger will NOT recover the batery. In that case seperate the batteries and charge each one with an automotive battery charger.

Go to Pride's website. You can download the operators manual and the service manual there.

The number of flashes indicate the problem. Go to Pride's website to download the service manual. It will tell you what the flashes mean and how to fix it.

Sounds like the switch itself.. the black button.. is defective. Best case is, the Pride dealer that sold the chair will fix it. If they sold the chair to you, and billed insurance to pay for it, they should bill insurance to pay for the repair. Call the dealer. If you're on your own, you need to find the part. Does this look like it would fit? http://www.monsterscooterparts.com/keypad-2-key-gc-joystick-jazzy-select.html

If you are moving as soon as you turn on the chair, the lights will move from right to left. Try waiting a few seconds and see if the lights stop moving. If they do stop, then you can move forward. Hope this helps.

Here you go: Pride Mobility Products Corp Jazzy Power Chairs Pride Mobility Scooters Go...

A 9 flash indicates a brake issue. Make sure the motors/brakes are both locked into gear before turning on the chair. It could mean that one of the motors is unplugged from the main controller or a wire is broken between the motor/brake and the main controller.

This is a cable disconnect code. Follow the cable going from your joystick controller to where it connects to another wire under or behind your seat. Disconnect and reconnect. You also will want to look at the cable closely for any pinches or cuts. This will also cause the 9 flash code.

I would think there is a communication error from the joystick to the controller. One time i had this and one of the plug ends was broken off from the joystick cable. Make sure all the plug tips are straight and not missing or broken on the joystick cable and also on the joystick and controller. it could be a simple fix like replacing the cable, but if you have a broken part in the controller or the joystick ports you will have to replace the defective part.

this could be a right brake fault or a controller fault. Check and see if the right motor has been disengaged. The easiest way to chreck this is to try and push on the right side of the chair. if the wheel begins to turn then the motor has been disengaged and you should be able to re-engage the motor and stop the wheel from turning. At this point you will have to turn off the chair and turn it back on to see if the fault goes away. If that is not the problem then it could be a loose motor connection. Check all your wiring connections on the motor to the controller. The other problem it could be is a controller fault. check all the connections on the controller and the wiring. Turn it off and back on to see if the fault goes away. If the fault is still there you will probably need to contact a service tech for them to get on line with the controller and find the root cause. They should have the diagnostic tools to check this.

About the only thing you can do is change the brushes and clean the comutator .. otherwise send it out and have it rebuilt .. new bearings, rewhind motor etc. Or go on ebay and find one

The fan on the charger should always run when the charger is plugged in. This is what keeps the components in the charger cooler. Most people just leave the charger plugged into the wall and just unplug the chair. The fan is still running. This is part of the reason for a lot of chargers failing. You will need to replace the charger. This is not a maintenance component.

Gosh I am sorry but have NO knowledge Re: Quantum chair chargers but unless you got your chair and equipment from Scooter Store. which got shut down by Feds due to fraud, you might contact chair's supplier and ask about getting a replacement for your destroyed charger's source. Failing that, does your city/county publish a "throw away" paper? Sometimes one can find powerchair's equipment posted there. That might be worth a try. I am sorry not to be familiar with Quantum mobility aids! Anybody else, please?

I have no idea as I don't have a jazzy select lift chair. Sorry

Typically when a joystick flashes 9 times, it indicates there is a problem with the solenoid brake(s). I recommend contacting Pride Mobility for a Certified Technician in your area to look at this chair.

It could be a brake trip/free wheel it could be a communication fault. This is usually an intermittent connection in the circuit. I would make sure all connectors are secure. The best way to do this is to disconnect and reconnect. Even do the ones going into the controller also. if these do not help, you may need a tech to check it out. They will go thru the same process. The only additional thing they can do is get online with the controller with a programmer that will give them additional fault codes that sometimes can be more specific as to what the problem is. I think it's most likely a brake fault. Make sure the freewheel on both motors are in the engaged/locked position. Worst case, your controller may be bad.

Yes, this can be accomplished by lowering the seat or raising the foot platform.The cushioned van seat can be removed from the seat frame and a wood platform covered in vinyl can be substituted. Sticky back Velcro strips are put on the vinyl cover to hold the cushion. The sticky back Velcro attaches to the vinyl covered wood platform and will mate up with the Velcro on the bottom of her existing cushion. The back cushion can be left in place. Pride makes this flat platform for all their models. You would need to specify the dimensions and style of the original seat to order the custom one. There is a manufacturer sticker under the seat with a series of numbers you can give to customer service at pride to help get the correct replacement platform. You can also raise the foot platform on the vertical adjustment post or attach a foot platform to the top of the footplate. If this modification is not covered by insurance you can have a handyman remove the cushioned van seat and hack off the cushioned foam, springs and vinyl. He could then cover the wood with a durable material or sand and paint it before reinstallation. Hope this helps.