Top 20 Pride Jazzy Select 6 Indoor Power Wheelchair Questions & Answers

It is not uncommon for a controller to continue flashing while it is charging. However, the fact that your controller still flashes 7 after you have exhausted and repaired it suggests that there may be a deeper issue with the controller. It is possible that there is a problem with the battery, the charging port, or the circuit board. If you have exhausted all of the troubleshooting steps that you are comfortable with, it may be best to contact the manufacturer or a professional repair service for further assistance.

Question edited for clarity. Question moved form Car Audio to Pride Jazzy Select 6. 9 Flashes The park brakes have a bad connection. Check the left and right motor connections and wiring. Check to make sure that the power chair is not in freewheel mode.

jazzy select - Any electromechanical device requires ...

Videos as well https://www.google.com/search?q=jazzy+select+6+blinks+9+times& ..

You have two good batteries in the green side, the red light means that one or both batteries are not fully charging. Try that set on the other side to confirm. Make sure the batteries and charger connections are clean.
Hope this helps.

My tires squeak how can i fix the problem and what ... - Fixya

www.fixya.com > ... > Pride > Jazzy Select 6 Indoor Power Wheelchair

Apr 14, 2012 - my tires squeak how can i fix the problem and what can i use - PrideJazzy ... Question about Pride Jazzy Select 6 Indoor Power Wheelchair ... I have a mpv 5 hoveround wheel chair and I now have a flat on the front left tire.

[PDF]Jazzy Select Series Owners Manual - Pride Mobility Products

www.pridemobility.com/...jazzy/us_select_series_om.pdf

Pride MobilityJazzy Select 6 with Power Seat. JAZZY. SELECT SERIES. Including Models: Jazzy Select, Jazzy Select 6, and .... Battery charger for indoor use only. .... Take wide swings with your power chair's front wheels around any tight corners. ... desired, allow it to come to a complete stop by releasing the joystick, then push the ...

[PDF]Jazzy Select Series - Pride Mobility Products

Yes. Change the potentiometer behind the throttle lever. It's probably 10 ohms. Try a lower resistance pot. It will run the battery down quicker though.

This is usually one of two things. You will need to pry the on/off button away from the joystick for inspection. Use a utility knife to get under the edge and pry it off. The back of the rubber button is coated with a material that conducts electricity so that when you press it, it makes contact with the surface under it which is also conductive. 1. For older chairs that get a lot of on/off use, this metalic coating on the back of the switch can wear away and not make good contact with the base. Examine the back of the on/off button for wear; you will see the rubber under the metalic coating if it is worn. Pressing around the edges of the button might work to get it on and off, or pressing harder. Otherwise, you need to paint on a new coating. Here is a site that sells that product. http://www.newark.com/chemtronics/cw2605/conductive-chemical-coating-3g/dp/00Z1875?mckv=sskjVGufT'pcrid'57087234861'plid'&CMP=KNC-GPLA 2. If you have spilled something on the joystick that has fouled the connection here, it will have a hard time making contact to turn on and off. Clean with alcohol and cotton swabs, let dry and see if that does the trick.

Sounds like the switch itself.. the black button.. is defective. Best case is, the Pride dealer that sold the chair will fix it. If they sold the chair to you, and billed insurance to pay for it, they should bill insurance to pay for the repair. Call the dealer. If you're on your own, you need to find the part. Does this look like it would fit? http://www.monsterscooterparts.com/keypad-2-key-gc-joystick-jazzy-select.html

A 9 flash indicates a brake issue. Make sure the motors/brakes are both locked into gear before turning on the chair. It could mean that one of the motors is unplugged from the main controller or a wire is broken between the motor/brake and the main controller.

Check to see if both motors are engaged. If not the problem, most likely controller has a short in the circuit board.

Here you go: Pride Mobility Products Corp Jazzy Power Chairs Pride Mobility Scooters Go...

I would think there is a communication error from the joystick to the controller. One time i had this and one of the plug ends was broken off from the joystick cable. Make sure all the plug tips are straight and not missing or broken on the joystick cable and also on the joystick and controller. it could be a simple fix like replacing the cable, but if you have a broken part in the controller or the joystick ports you will have to replace the defective part.

this could be a right brake fault or a controller fault. Check and see if the right motor has been disengaged. The easiest way to chreck this is to try and push on the right side of the chair. if the wheel begins to turn then the motor has been disengaged and you should be able to re-engage the motor and stop the wheel from turning. At this point you will have to turn off the chair and turn it back on to see if the fault goes away. If that is not the problem then it could be a loose motor connection. Check all your wiring connections on the motor to the controller. The other problem it could be is a controller fault. check all the connections on the controller and the wiring. Turn it off and back on to see if the fault goes away. If the fault is still there you will probably need to contact a service tech for them to get on line with the controller and find the root cause. They should have the diagnostic tools to check this.

If you are moving as soon as you turn on the chair, the lights will move from right to left. Try waiting a few seconds and see if the lights stop moving. If they do stop, then you can move forward. Hope this helps.

The number of flashes indicate the problem. Go to Pride's website to download the service manual. It will tell you what the flashes mean and how to fix it.

Gosh I am sorry but have NO knowledge Re: Quantum chair chargers but unless you got your chair and equipment from Scooter Store. which got shut down by Feds due to fraud, you might contact chair's supplier and ask about getting a replacement for your destroyed charger's source. Failing that, does your city/county publish a "throw away" paper? Sometimes one can find powerchair's equipment posted there. That might be worth a try. I am sorry not to be familiar with Quantum mobility aids! Anybody else, please?

The fan on the charger should always run when the charger is plugged in. This is what keeps the components in the charger cooler. Most people just leave the charger plugged into the wall and just unplug the chair. The fan is still running. This is part of the reason for a lot of chargers failing. You will need to replace the charger. This is not a maintenance component.

I have no idea as I don't have a jazzy select lift chair. Sorry

About the only thing you can do is change the brushes and clean the comutator .. otherwise send it out and have it rebuilt .. new bearings, rewhind motor etc. Or go on ebay and find one

Go to Pride's website. You can download the operators manual and the service manual there.

Until the green light o the charger comes on or the charge meter shows one amp or less. If the batteries were drawn down too far the 5 amp charger will NOT recover the batery. In that case seperate the batteries and charge each one with an automotive battery charger.