20 Most Recent Magic Chef 9512 Electric Single Oven - Page 7 Questions & Answers

GLO-SIL IGNITOR MAY LOOK LIKE IT'S WORKING BUT IT'S PROBABLY NOT GETTING HOT ENOUGH TO ALLOW RESISTANCE TO FLOW BACK TO BURNER VALVE AND WARP SWITCH TO ALLOW GAS TO FLOW TO BURNER. REPLACE IGNITIOR

If these parts are available you can find them at www.repairclinic.com and www.apdepot.com make sure you have your model number and serial number handy If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

Hello there, you can buy the glass front here:

http://www.partstore.com/Part/Maytag/Maytag/59E5EXW/Whirlpool/Whirlpool/7902P12060/New.aspx

It will include installation instructions that you need, and yes with an off-set screw driver you can remove the glass front.

Thanks!
Tim

Why don't you plug it in?

First of all, thank you very much Vincent for choosing FIXYA today for your online technical support needs. I'm Joe, and I will be more than happy to assist you with your service request. Here is a direct link to the ONLINE USER'S MANUAL for that model:http://shared.whirlpoolcorp.com/assets/pdfs/literature/34HA-2CKXW-ON.pdfAnd here is the link to the exploded view parts diagram / parts list for that model if you needed it:http://www.appliancepartspros.com/partsearch/model.aspx?model_id=41455 To view the Owner's Manual with Operating Instructions or the Parts Diagram just use your mouse to click on the links, which are the underlined and blue highlighted sections of text just above. This will open a new web browser page automatically for you and allow you to view the information at the website indicated and the contents of the Owner's Manual. You may need ADOBE READER installed on your computer to read PDF documents, although many computers already have this utility pre-installed. You can always download this for free at WWW.ADOBE.COM if necessary. Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there, then follow the onscreen instructions to install the software on your computer. Please COMMENT back here to this page if you have any details to add, have any questions, have difficulty accessing the links, or just require further general assistance and I will respond as soon as I see it. If you were satisfied with the service provided, could you please take a moment to leave a 5 STAR rating. Your feedback is very important and I truly appreciate your consideration. BEFORE leaving a rating OTHER THAN 5 STARS or a negative TESTIMONIAL, please contact me using the ADD A COMMENT feature and I will immediately clear up any concerns or answer any additional questions that you might have until you are completely satisfied with the service provided. The FixYa rating system is a very important component of the Marketplace, and unfortunately once you post a rating or a testimonial to a solution, it cannot be changed at all later on. Be sure to use the small blue ADD A COMMENT button located just below the text of this solution to leave any additional comments for me regarding this particular issue and I will respond right away. I truly hope that was helpful to you. Good luck and take care. Joe.

Hello,The error code's F3&F4 are codes that mean their is a problem with the oven tempature sensor and that sensor is uncappable of telling the control board what the temp. is in the oven. This is what the sensor looks like,To check the sensor,unplug it and place meter leads into the white plastic plug at the end and check for between 1060-1100 ohms of resistiance when its good.The F3 error code means that the sensor is shorted so if it indeed is shorted the meter reading will show ZERO ohms resistiance instead of the 1060-1100 of a good one.The F4 error code is for sensor that has a open circuit,so instead of the 1060-1100 of a good it the display on the meter will show infinate resistiance ( the meter display will not change) If on either the F3/F4 error code if at room tempature when checking the oven sensor if the display shows anything other that 1060-1100 ohms the sensor is going to be the problem and needs to be replaced.

Hi Nancy:Error Code F2 indicates a loose or broken wire on the oven temp sensor or the oven temp. sensor itself is bad and should be replaced.Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective.Hope this helps; thank you for using Fixya. Keep in mind that your feedback is important, leave us some testimonial comment.