Top 20 Magic Chef 9512 Electric Single Oven Questions & Answers

if the door is unlocked then clean all the grease and let go, if the oven is still locked then get a tech down to your house to have it unlocked since its not safe to have it run again with greaase

What you want to check or have checked is if the wiring on the new igniter was accidently not properly insulated and some or the wiring is bare and touching metel shorting the breaker each time the oven is turned on.

F1 Error Code - Defective touch pad or clock (ERC)

This simple test will help determine whether the ERC (Electronic Range Control or Clock) or the touch pad is defective when F1 error code is present.

Note: Some models incorporate the touch pad in to the ERC as a single assembly, in which case this test is not necessary. Simply replace the ERC (Clock).

Warning: If you feel in any way uncomfortable performing this test or making this repair, please contact a qualified appliance repair technician.

1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing.

2. Gain access inside the control panel.

3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.

4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.

5. Turn the power back on.

6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound).

7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.

Replace touch pad or clock (ERC). Touch pad is a more common problem. Refer to F1 test at the top of this page for more information.

Welcome to Fixya.


The problem could be:

1. Watchdog on board or
2. Touch membrane defective

To determine which component is at fault, disconnect ribbon strip. If NO fault code, replace membrane, otherwise replace board .

Thank you for using Fixya!

try to reset it ..by unplugging the oven ..and put it back after 30 minutes or so ...it may be a function set ..and remained there ...if the fan is not stopping ..than it is probably a wire that has a bad connection and feed s it with electricity when it not supposed to...probably the isolation went off from the heat ...and in this case you need to call for a specialized hand to see the short and fix it ..

Sounds like a Thermostat problem, perhaps sensor has gone faulty?

this is usually a temp sensor probe problem.check you wiring between the probe and the electronic control board. at room tempt check the resistance on the probe if it less than 500 ohms replace the probe.

Hi, If the oven is still locked the problem will be the latch you will need to replace it. If the oven is not locked then the igniter was damaged during the clean and you should replace the igniter.If you have any further questions please feel free to comment. Mike

Usually L1 is a code for power on. So try to clear it by pushing enter or clear and see if it helps.

Please rate me accordingly if this helps and good luck.

If the ignitor fails to pull at least 3.5 amps then it is bad. Go get another ignitor. That one is defective. If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

If it has a timer, make sure it is set to manual,and not flashing auto.
In the auto mode the oven will not work.
Plz rate this solutioin.
Thanks.

you can check you connections to see if loose wire nut.normaly people will say they hit the oven safty valve and gas will come out.the amp draw on that ignitor is as ive been taught 3.2 to 3.5 if low than that it will have a hard time opening the safty valve.ive sold and installed 100s of ignitors and a few valves.hope that helps.god bless tom

hi .thanks for the question . A very common problem with gas ovens replace the igniter thanks the appliance doc

push in on the themostat when the oven is on piolt hold a lighter under the burner and presto also light the stove to get gas flowing first this can take up to fifteen min to light if it has been awile since lit

Hi - Please post the model number of you appliance, it will look something like CEC1536.

Thanks.

hi. Thanks for the question. The problem is with the igniter . Replace it it is located under the floor of the oven .thanks the appliance doc

YOU HAVE A BAD ELECTRONIC RANGE CONTROL OR ERC If you need further help, reach me via phone at https://www.6ya.com/expert/marlon_56d9a24f02585258

Yes this is normal. you can use that burner to keep things warm without turning it on, saves energy.

thats an electronic oven control any appliance repair store can get you one if not try here http://www.repairclinic.com/SmartSearch/smartsearch.aspx