Top 20 DeLonghi DE500 Dehumidifier - Page 7 Questions & Answers

The Units are made in the Far East and are often sold under different maker names but retaining all or part of the model number. Here is the manual sold by Evantair. It has a compressor.https://www.manualslib.com/manual/1016879/Evantair-Wdh-816eah.html#manual..

Can you give a little more detail about the problem? Is it turning on? Is there just no water collecting?

'make model (what it is)' first 3 words in every question please. You could have three issues. 1. a drain plug not removed 2. an airlock 3. a blockage caused by biofilm gunk. Nasty stuff. Try blowing air UP the drain hose. ..

I would check the position of the sensor and make sure it is clean and free from debris.

Question edited for a lot more clarity, add maker, fix English. It sounds like a refrigeration issue like low gas. There are various idea here, but you probably need to drop it off at a refrigeration service centre. https://www.google.com/search?q=gd2005+dehumidifier+starts+and+stops+working ..

Not listed.... ck here..... https://www.cpsc.gov/Recalls/2023/Gree-Recalls-1-56-Million-Dehumidifiers-Due-to-Fire-and-Burn-Hazards-Reports-of-At-Least-23-Fires

It sounds like the switch needs to be replaced or adjusted. https://www.google.com/search?q=Haier+Dehumidifier+says+bucket+full Need model number. That is needed in all Fixya questions. https://www.google.com/search?q=haier+dehumidifier+parts+list ..

If water is coming out on the floor from your Comfort Site dehumidifier even when the bucket is not overflowing, there may be a few possible causes for this issue:

1. Improper Placement of the Bucket: Ensure that the bucket is correctly positioned and inserted into the dehumidifier. Make sure it is securely in place, and the water outlet on the bucket is aligned with the dehumidifier's drainage system. If the bucket is not properly seated or aligned, it can result in water leakage.
2. Bucket Seal or Gasket: Check the bucket's seal or gasket for any signs of damage, wear, or misalignment. If the seal is compromised or not making proper contact with the dehumidifier's body, water can escape and leak onto the floor. Clean the seal and ensure it is free from debris or obstructions. If necessary, replace the seal or gasket with a compatible replacement part.
3. Drainage Hose Connection: Some dehumidifiers have the option to connect a drainage hose directly to the unit for continuous draining. If a drainage hose is connected, make sure it is securely attached and there are no leaks or loose connections along the hose. Ensure that the other end of the hose is properly directed into a drain or receptacle.
4. Internal Drainage System: The dehumidifier's internal drainage system, including the collection tray or drain pan, may be clogged or blocked. Remove the bucket and inspect the drainage area for any debris, buildup, or blockages. Clean the drainage system thoroughly, ensuring that water can flow freely from the collection tray into the bucket without any obstructions.
5. Check for Excessive Humidity: If the dehumidifier is operating in an area with extremely high humidity levels, it may struggle to remove moisture effectively. This can result in excessive condensation or water buildup that leads to leakage. Consider using additional dehumidification methods or addressing the underlying humidity issue in the space.

If the issue persists after checking these potential causes, it is advisable to consult the user manual for your specific Comfort Site dehumidifier or contact the manufacturer's customer support for further assistance. They can provide specific troubleshooting steps or offer guidance based on their knowledge of the product.

copy and paste link page 21, also in your manual. https://www.honeywellstore.com/store/images/pdf/honeywell-tp-series-dehumidifier-manual.pdf

Parts Suppliers. Replacing the sensor seems to be the fix. https://www.google.com/search?q=Noma+Dehumidifier+043-5795-6+Parts+sensor

If your Norpole dehumidifier is repeatedly starting and stopping, it could indicate a problem that needs to be addressed. Here are a few troubleshooting steps you can try:

1. Check the humidity settings: Ensure that the humidity level set on the dehumidifier is reasonable and not too low. If the desired humidity level is already reached, the dehumidifier may turn off until the humidity rises again.
2. Clean the air filter: A dirty or clogged air filter can restrict airflow and cause the dehumidifier to overheat. Turn off the dehumidifier, unplug it, and locate the air filter. Remove the filter and clean it according to the manufacturer's instructions. Allow it to dry completely before reinstalling it.
3. Check the water collection bucket: If the water collection bucket is full, the dehumidifier may automatically shut off. Empty the bucket and ensure it is properly positioned back into the unit.
4. Verify the drainage system: If your dehumidifier is equipped with a continuous drainage option, make sure the drainage hose is properly connected and not clogged. If the drainage hose is obstructed or improperly installed, it can cause the dehumidifier to turn on and off.
5. Ensure proper ventilation: Make sure the dehumidifier is placed in a well-ventilated area. Restricted airflow around the unit can lead to overheating, triggering the auto shut-off feature.
6. Power supply issues: Check the power cord and make sure it is securely plugged into a functioning power outlet. Also, ensure there are no issues with the circuit breaker or electrical supply.

If none of these steps resolve the issue, it's recommended to consult the user manual or contact Norpole customer support for further assistance. They will be able to provide more specific troubleshooting steps or advise on potential repairs or service options.

https://evaly.com.bd/products/baseus-hd-convex-blind-spot-auto-rearview-car-mirror-silver-8458491

The easy way is to turn it upside down. Leave 12 hours before turning back on. Or you can removed the back panel and then the side panels. The screws are hidden under small removeable plugs. Or you can use one of these to reach in and grab it. https://www.walmart.ca/en/ip/Agiferg-Flexible-Long-Reach-Claw-Pick-Up-Narrow-Bend-Curve-Grabber-Tool-Spring-Grip-80cm/1Z9FN1CNSYCW ..

Question edited to add full 'make model (what it is)'. Some models have a bucket, and some don't as it can be optional. Its capacity is 30 pints per day. The manual and the specs for the 3 models in the range are in the link. https://manualzz.com/doc/2052238/goldstar-dh3010b-dehumidifier-user-manual ..

Jay, Check here... https://www.appliancefactoryparts.com/airconditioners/everstar/mpn1-095cr-bb6.html#Hoses,-Valves,-and-Regulators Best to you.

There could be several reasons why the humidity reading on the digital control is not accurate. Here are a few things you can try:

1. Calibrate the hygrometer: The first thing to do is to make sure that the hygrometer you are using to measure the humidity is calibrated correctly. You can check this by placing the hygrometer in a sealed container along with a wet sponge or cloth for a few hours. The hygrometer should read close to 100% humidity. If it doesn't, then it may need to be calibrated.
2. Check the humidity sensor: The humidity sensor in the incubator may be faulty or dirty. You can clean the sensor with a soft cloth or replace it if it is damaged.
3. Check the water level: Make sure that the water level in the incubator is sufficient. If the water level is low, the humidity will be low as well.
4. Check the ventilation: The ventilation in the incubator should be set to allow for proper air exchange. If the ventilation is not set correctly, it can affect the humidity level.
5. Check the room conditions: The room conditions, including temperature and humidity, can affect the humidity level in the incubator. If the room is too dry, it can affect the humidity level in the incubator. You may need to adjust the dehumidifier or add a humidifier to the room to maintain the proper humidity level.

I have one that did the same thing. I had to raise it about 1-2 feet to get it to drain properly.

There are several reasons why your T2 Direct Dehum 3 dehumidifier may be alarming after running for a few seconds:

1. Dirty or Clogged Air Filter: A dirty or clogged air filter can cause the dehumidifier to overheat and shut down. Check the air filter and clean or replace it if necessary.
2. Defective Humidity Sensor: If the humidity sensor is defective, it may cause the dehumidifier to shut down. The sensor may need to be replaced.
3. Faulty Compressor: A faulty compressor can cause the dehumidifier to shut down after running for a short time. You may need to replace the compressor.
4. Low Refrigerant Charge: If the refrigerant charge is low, it can cause the dehumidifier to shut down. You may need to recharge the refrigerant.
5. Faulty Control Board: A faulty control board can cause the dehumidifier to shut down or display error messages. You may need to replace the control board.

It is recommended to contact a qualified technician to diagnose and repair the issue with your dehumidifier.

It sounds like your dehumidifier is likely experiencing an issue with the condenser. If the container was half filled, then it's possible that the condenser has become clogged due to a buildup of sediment or debris. To fix this, you should unplug the unit and remove the cover to check for any blockages. If there are any, then you can use a vacuum cleaner or compressed air to remove them. Additionally, you should also inspect the condenser for any signs of wear or damage. If the condenser is cracked or damaged, then it will need to be replaced. If you need further assistance, you can consult a professional technician for diagnosis and repair.

'make and model' are needed in all questions please. However it appears to be Noma or Hisense. See videos and articles. https://www.google.com/search?q=Dehumidifiers+error+E9 ..