Top 20 Jura Capresso Impressa E8 Espresso/Coffee Maker Questions & Answers

The hooks in the lid are tricky to remove without breaking. It is best to remove the top cover. To do so you need special key to open the machine. Order the special key from the link below. Watch the video posted on You tube channel "Parts Guru USA". Descale the machine every three months using manual descaling. Jura instructions are misleading and create unnecessary error messages. Services Unlimited Inc Parts Guru Since 1988 Services Unlimited Inc Parts Guru Since 1988 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Check the membrain regulator for leaks. Those end up leaking over time as they get older. They look like this: http://i.ebayimg.com/00/s/MTYwMFgxNTk5/z/XMAAAOSwl8NVdZz4/$_35.JPG and are located on the outlet side of the water pump. They can be bought for about $50-60 and just screw on to the outlet side of the pump.

Operating Manuals - Jura Capresso Coffee Machines

capresso.125west.com/html/operating_manuals.html Operating Manual Impressa F9 and F9 Limited Edition. Operating Manual Impressa F7. Operating Manual Impressa E8. Capresso C1300 Superautomatic ...

I would say that something has a hole in it, but if it doesn't it might have bad quality, and if it isn't that because the place where you bought it from sells good machines, then it still might have something that went wrong or something was misplaced. I'm not sure either, but that's what i think is the most likely reason. You could always try ask the place manager and ask him if there is anything wrong with your machine. Hope it ind of helped!

Difficult to say without the machine in front of me. Normally you get this response if no beans fall into the grinder. Are your beans oily, sticking together and not falling in? Normally freshly roasted beans esp dark roasts are a bit oily. If so then you can change roasts, brands or mix with another type. You might try to adjust your grind per the manual. (turn knob inside the bin while the grinder is grinding) see #8 page 12. If the beans are falling in and grinding and you still get this msg I would say you have a grinder problem. http://capresso.125west.com/e8_manual.pdf

Sounds like you might have more than one problem. From page 12 of the manual... NOTE THE LAST LINE. "8. ADJUSTING THE GRINDER ...... • Open the lid of the bean container. • While the grinder is running turn the grind selector switch to the desired position (Fig. 6). -The smaller the dots, the finer the grind. -The bigger the dots, the coarser the grind. Important: The grinding grade can only be adjusted while the grinder is actually grinding."

So did you empty the grounds? Pull the plug and plug it back in. There is an encoder disk that spins around to control the mechanical movements inside the unit. Some mechanical piece is not where it is supposed to be and the circuit board it waiting for a sensor to clear. Cycling the power will normally make all the mechanics reset to the start position and clears errors/jams etc.

Here is a list with the error codes, hope it helps. Jura Error Codes Capresso Parts

Hi Jill our coffee machine is built in and not your brand but our problem related to a sensor at the back of our tray which had broken off we found it and glued it back on which worked for a little while in the end we replaced the tray and have had no further problems. Hope this help. Cheers Wayne

2 things descale the unit as per user book or make the grind coarser. this is done in or near the coffee beans container. turn the knob in the direction of the larger dot or bean symbols

This one is easy. Remove the tray then unplug the machine. Wait a full five minutes then put then put the tray back In WITHOUT the box. Plug it back in. It will recycle and the flap will behave again. FYI make sure that each time you remove the grounds you find the screen behind and above the flap and clean it with a wet paper towel. It's the size of a nickle and gets clogged if you don't do this.

Open the tap with frother spout off. This happened to mine and I took the frother tip off and opened tap with tip off. Water filled and I closed tap...Machine returned "Ready". I heated water in microwave for three minutes- placed frother tip in hot water and all kinds of gunk came out. Lesson learned- Do a thorough cleaning of frother by immersing it in very hot water at least once monthly- even if you don't use it

There should be oval-headed screws in the machine. You need a special tool to turn them. I got one from the jura capresso doctor on ebay.

all the instruction manuals are on the jura website, capresso.com, you can download the one you need and all instructions are there.

this was absolutely the problem with my Jura Capressa E-8 machine. I followed instructions after changing the filter. I opened tap-machine stated that it was filling system- I closed tap when instruction. The open tap remained on because no water was filling system. I took the frother tip off and opened tap. Water filled system (container under frother). I closed tap without the frother tip. Machine Ready.... (I heated water in microwave for three minutes) I placed the frother tip in there and used a wooden skewer to ensure frother was clear of debris... Worked like a charm!

For Jura F7 Series, "Tray Missing, can't put it back in". With a small flashlight, look in to the cavity which the tray and grounds container reside in. Along the right side above a slot to the end, you'll see a white micro switch. with a "Tooth Pick" simply press the switch inward (to the right) and hold till the machine cycles the Levcer / Flap up and out of the way.! Put your tray and grounds container back in and begin brewing!! -dh

Hi Glen MANUALS & Instruction Books are On Line The drivers & Books & manuals are more than likely on the manufacturers site. They usually can be downloaded for currently available devices. Search their support area for your specific model of device. Try Google Search for a Manual or PDF File for the specific brand & model number. Also check these Sites: www.retrevo.com .... Manuals www.office.manualsonline.com