Jura Capresso Impressa E8 Espresso/Coffee Maker - Answered Questions & Fixed issues
Why fill bean message shows on display when machine is full of beans?
Difficult to say without the machine in front of me. Normally you get this response if no beans fall into the grinder. Are your beans oily, sticking together and not falling in?
Normally freshly roasted beans esp dark roasts are a bit oily. If so then you can change roasts, brands or mix with another type.
You might try to adjust your grind per the manual. (turn knob inside the bin while the grinder is grinding) see #8 page 12.
If the beans are falling in and grinding and you still get this msg I would say you have a grinder problem.
http://capresso.125west.com/e8_manual.pdf
Brew temperature is too low
I think you ment kaffeestudio.de and their webshop redirects to
http://www.juraprofi.de/Service-Anleitungen:_:70.html
Eg http://www.juraprofi.de/anleitungen/E-Serie_Innen.pdf
Jura capresso shuts down
It is possible that the timer unit in the maker is defective and need to be replaced. I would suggest you move the coffee maker to a different outlet and see if you have the same problem. If there is a short in the mechanism or a bad connection in the timer it could be experiencing a thermal shutdown.
Grind time is short, puck is wet and sloppy, espresso weak
Sounds like you might have more than one problem.
From page 12 of the manual... NOTE THE LAST LINE.
"8. ADJUSTING THE GRINDER
......
• Open the lid of the bean container.
• While the grinder is running turn the grind selector switch to
the desired position (Fig. 6).
-The smaller the dots, the finer the grind.
-The bigger the dots, the coarser the grind.
Important:
The grinding grade can only be adjusted while
the grinder is actually grinding."
10/23/2014 5:57:52 PM •
Jura Capresso...
•
Answered
on Oct 23, 2014
•
2,547 views
Why empty grounds message stays
So did you empty the grounds?
Pull the plug and plug it back in.
There is an encoder disk that spins around to control the mechanical movements inside the unit. Some mechanical piece is not where it is supposed to be and the circuit board it waiting for a sensor to clear. Cycling the power will normally make all the mechanics reset to the start position and clears errors/jams etc.
The flap will not go all the way up so the drawer can go all the way in
This one is easy. Remove the tray then unplug the machine. Wait a full five minutes then put then put the tray back In WITHOUT the box. Plug it back in. It will recycle and the flap will behave again. FYI make sure that each time you remove the grounds you find the screen behind and above the flap and clean it with a wet paper towel. It's the size of a nickle and gets clogged if you don't do this.
Missing drawer light on but drawer is in place
Hi Jill our coffee machine is built in and not your brand but our problem related to a sensor at the back of our tray which had broken off we found it and glued it back on which worked for a little while in the end we replaced the tray and have had no further problems. Hope this help. Cheers Wayne
Jura impressa f9 malfunction 8 i need help whats
Malfunction 8 means that the brew unit can not get in the right position in the right time. This is usually because the brew unit is full of old coffee grounds. Try to shut down the machine for one day. The next day, take out the tray and clear out all coffeegrounds inside the brewunit. Use your fingers and maybe a small towel. You can do this right away, but it is easier when everything`s dried up. When all this is cleaned up, start manually a Cleaning program. This should solve your problem.
If it doesen`t, i could be that the o-rings inside the brew unit is defective and needs to be changed.
6/15/2013 3:45:20 PM •
Jura Capresso...
•
Answered
on Jun 15, 2013
•
2,096 views
Not finding what you are looking for?