02 Town and country with rear disc / 4 wheel anti lock. Right frnt brake drags intermitently. Caliper compresses normaly. Anti lock light on. Pads wear fast right frnt. Rotor gets too hot. Can an anti lock problem cause this.

It is possible that the slave pistons that apply pressure to the disc pads to engage the brake disc are dirty corroded and or seized.

A car mechanic will the the wheel off remove the disc breaks blast it out with air then apply isopropyl alcohol or some other non-lubricant cleaner to release them. If this doesn't work then they will need replacing.

Good question, on the antilock system is a bleader too and bleade it the same way you bleade the caliper. After all is done adjust the rear brakes, they should have a drag to them.

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly









4.0L and 4.7L front disc brake assembly




To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
     and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.

1. Remove a small amount of brake fluid from the master cylinder.
   
2. Install a used brake pad into the caliper and compress the caliper pistons.
   
3. Apply disc brake grease to both sides of the inner anti-squeal shims.
   
4. Install or connect the following:
   
   
   
   • Anti-squeal shims to the new brake pads
     NOTE: When replacing worn pads, the anti-squeal shims must be replaced
     together with the pads.
     
     
   • 2 brake pads
     
   • Anti-rattle spring and the 2 caliper pins
     
   • Clip
     
   • Front wheel
   
   
5. Depress the brake pedal several times to seat the brake pads.
   
6. Check the brake fluid level and top off as needed.

Rear
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Rear wheel
     
     
     
     
     
     
     
     
     
     
     
   • 2 cylinder slide pins from rear caliper assembly
     
   • Caliper assembly from rear caliper mounting
     
   • 2 brake pads with anti-squeal shims from rear caliper mounting
     
   • 2 anti-squeal shims from each disc brake pads
     
   • Pad wear indicator plate from the inner side disc brake pad
     
   • 4 pad support plates from the rear caliper mounting

To Install:

1. Install or connect the following:
   
   
   
   • 4 pad support plates on the rear caliper mounting
     
   • Pad wear indicator plate on the inside brake pad
     Note: Install the pad wear indicator facing downward.
     
     
   • Anti-squeal shims on each brake pad
     
   • 2 disc brake pads with anti-squeal shims to the caliper assembly
   
   
2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
   pins.
   
3. Install or connect the following:
   
   
   
   • Disc brake caliper assembly with 2 caliper slide pins
     
   • Torque to 65 ft-lbs (88 Nm)
     
   • Rear wheel
   
   
4. Depress the brake pedal several times to seat the brake pads.
   
5. Check the brake fluid level and top off as needed.

--- Removal & Installation
Front
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Front brake caliper assembly
   
   
3. Make matchmarks on the disc and the axle hub.
   
4. Remove the front disc.

To Install:

1. Align matchmarks and disc onto axle hub.
   
2. Install or connect the following:
   
   
   
   • Front brake caliper assembly with the 2 bolts
     
     
     
     1. Torque to 90 ft-lbs (123 Nm)
     
     
   • Front wheel

Disc Brake Pads for Suburban 1500 Removal & Installation Front To Remove:
Front caliper mounting bracket

1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
2. Raise and support the vehicle safely.
3. Remove the wheel and tire assembly.
4. Compress the brake piston back into its bore using a C-clamp.
5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
6. Remove the inboard and outboard pad.
7. Remove and discard the anti-rattle clips.

To Install:
Caliper bracket sleeves

1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
2. Install new anti-rattle clips.
3. Position the inboard and outboard pads into the support bracket
4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
5. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
6. Tighten the mounting bolts to: 80 lb. ft, (110 Nm).
7. Install the tire and wheel assembly. Lower the vehicle.
8. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
9. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.

Rear To Remove:

1. Remove 2/3 of the brake fluid from the master cylinder.
2. Raise and safely support the vehicle.
3. Remove the wheel and tire assembly.
4. Remove the brake caliper mounting bolts. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
5. Remove the brake pads from the caliper mounting bracket.
6. Remove and discard the anti-rattle clips.

Rear brake caliper

To Install:

1. Install new anti-rattle clips.
2. Position the brake pads to the caliper mounting bracket.
3. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
4. Install NEW caliper mounting bolts. Tighten to: 30 lb. ft, (40 Nm).
5. Install the wheel and tire assembly.
6. Lower the vehicle.
7. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly to seat the brake pads. Burnish the brakes as needed.

Remove all rust from pad and caliper sliding surfaces,eg metal to metal,not the pins,they get synthetic brake lube. Apply anti-seize to all sliding surfaces. Make sure you can screw in the rear caliper piston,if applicable, and manually ratchet up the parking brake,after caliper and pads are on. Bleed/Flush all 4 Wheels. Make sure you can slide the pads back and forth,before lubing end tabs. You may need to file a little off the ends or just remove the paint. Make sure parking brake cables are really releasing.

You are not suppose to open the bleeders when replacing the brake pads.After pad removal you compress the pistons into the calipers and install new pads after cleaning and lubing the slides.Then just pump the pedal til it comes back up.Usually takes about 3 or 4 pumps.Make sure you didn`t break a brake line.If there were any problems with the anti lock brakes the light would come on.Hope this helps.Let me know.Good luck.

to remove the rear brake pads you must first remove the caliper slides bolts and compress the caliper pistons them the caliper will remove easily

1.Remove the cap from the brake fluid reservoir

2.Loosen the wheel nuts then raise the vehicle and remove wheel

3.Push the piston back into the bore to provide room for the new brake pads.A C-clamp can be used to accomplish this As the piston is depressed to the bottom of the caliper bore the fluid in the master cylinder will rise.Make sure is doesnt overflow.If necessary drain off some of the fluid. 4.Before removing anything,spray the disc,and brake pads with brake system cleaner dont use compressed air 5.remove the caliper mounting bolt,the banjo fitting for the brake hose shouldnt be disconnected unless you are removing the caliper or hose replacement

6.Swing the caliper up and secure the caliper up towards the spring with a piece of wire then remove the lower and upper anti-rattle springs.Remove the outer brake pad and shim then remove the inner brake pad ans shim(s)

7.Remove and inspect the upper and lower pad retainer clips,the pad retainer clips should fit snugly in the caliper mounting bracket;if they dont,replace them.Apply thin film of high-temperature grease to the retainer

8.Apply anti-squel compound to the back of pads install the new inner pad and shim(s) make sure the "ears" on the upper and lower ends of the pad are fully engaged with their respective grooves and the pad retainer clips

9.Install the new outer pad and shim if new pad has no shim take the old shimoff the old pad and install it on the new outer pad.Install the upper and lower anti-rattle springs

10.Clean off the caliper pin and coat it with high-temperature grease.Lubricate the lower caliper pin with grease too thenswing the caliper down over the disc and new pads (if the piston hits the inner pad depress the piston further into the caliper bore with your c-clamp

11.Install the mounting bolt and tighten it to the torque specifications (44-63) 99 and earlier models (51-55)00 and later models
12.Put the wheel back on and tighten lug nuts

I had a similar problem with my anti-lock brake.
One of the will wear down. I took it to the dealer, could not tell why.
Until one day the a brake light came on. It was a bad sensor. Replace the bad sensor and the problem went away.
The mechanic plug a portable instrument and drive the car around until he find out. (The brake light came on, then off.)
This anti-lock brake system is control by sensors and it one is not functioning properly then you have a problem.
I do hope this help you.