Whats the torque on the head bolts - 1989 Ford Crown Victoria

2003 Cadillac CTS V6-3.2L VIN N - Justanswer

http://ww2.justanswer.com > uploads > joecamel90
PDF
Apr 16, 2010 - Tighten the cylinder head bolts to 25 Nm (18 ft. Tighten the cylinder head bolts to 90 degrees using the J 36660-A. Tighten the cylinder head ...
6 pages

What Is the Torque for the Heads - 2CarPros

https://www.2carpros.com > ... > Cylinder Head > Torque
Jun 29, 2010 - MEMBER; 2003 CADILLAC CTS; 6 CYL; 2WD; AUTOMATIC; 100,000 MILES. I am repairing the heads of this car. whats the torque I need to apply?

Complete Torque Specs List ' Cadillac CTS-V Forum

https://www.ctsvowners.com > threads > complete-torqu...
Jul 1, 2013 - Cylinder Head Core Hole Plug: 15 lb ft. Drive Belt Idler Pulley Bolt: 37 lb ft. Drive Belt Tensioner Bolts: 37 lb ft. Engine Block Coolant ...
Torque Specs??? - Cadillac CTS-V Forum
Apr 4, 2012
Torque Specifications ' Cadillac CTS-V Forum
Mar 8, 2012
Engine bolt torque specs, other - Cadillac CTS-V Forum
Nov 24, 2015
Factory head bolts reused ' Cadillac CTS-V Forum
Sept 11, 2014
More results from www.ctsvowners.com

When torque cylinder head bolts down you need to start in the centre and work ur way out .cylinder head bolts are torqued in 3 stages .
stage 1 25Nm
stage 2..50Nm
last step 73 Nm

Hi! Please don't forget to rate! Thanks!

Cylinder head bolt torque sequence-2.0L and 2.3L engines

Apply engine oil to the bolt threads and tighten the cylinder head bolts, in sequence, using the following 6 Steps:

• Step 1: 38.5 ft. lbs. (53 Nm)
  
• Step 2: 61 ft. lbs. (84 Nm)
  
• Step 3: Loosen all of the cylinder head bolts
  
• Step 4: 38.5 ft. lbs. (53 Nm)
  
• Step 5: 76 ft. lbs. (105 Nm)
  
• Step 6: Bolt M6 (bottom left of cylinder head) - 8 ft. lbs. (11 Nm)
  

To install:

Fig. Cylinder head bolt torque sequence-3.8L engine

1. Install the new cylinder head gasket with the arrow pointing to the front of the engine.
2. Install the cylinder head.
3. Install NEW cylinder head bolts. Torque the bolts in sequence, as follows:
   1. Step 1: 37 ft. lbs. (50 Nm).
   2. Step 2: Plus 120 degree turn.

To install:

Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines

1. Install the cylinder head with a new gasket.
2. Apply thread sealer to the head bolts.
3. Tighten the cylinder head bolts to 37 ft. lbs. (50 Nm) plus an additional 90 degree turn.

for the head

Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)

† Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)

† Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)

† Step 4: Bolts 1 - 8 turn an additional 1/4 Turn.

(Do not use a torque wrench for this step.)

NOTE: Bolt torque after 1/4 turn should be over 122
N·m (90 ft. lbs.). If not, replace the bolt.

Intake Manifold

Bolts . . . . . . . . . . . . . . . . . . . .23 N·m (200 in. lbs.)

Intake Manifold Gasket Retaining

Screws . . . . . . . . . . . . . . . . . .12 N·m (105 in. lbs.)

Intake Manifold Plenum
Bolts . . . . . . . . . . . . . . . . . . . .28 N·m (250 in. lbs.)
the pivot arm ? whats that

start in middle and work outwards alternately ,bolt torque 80lbs and pull down if three passes ,speed key --rachet- torque wrench .although iam posting this i never use a torque wrench i go by the feel of the bolt stretching ,make sure heads have been checked and skimmed before refitting

The cylinder head bolts need to be torqued at

• 10MM bolts 22 FT-LBS
• 12mm bolts 26 FT-LBS

Head bolt torque is 65 ft lbs, use the below sequence, go over bolts 3x to reach final torque (not all at once to 65)

13 5 2 10
front of engine 17 9 1 6 14
16 12 8 4 3 7 11 15
good luck!

2001 Daewoo Lanos Cylinder Head Bolt Torque Specs
Torque bolts in sequence
(looking down on the engine from front of car)

belts 1 3 9 5 7 trans
belts 2 4 10 6 8 trans

Step 1: 18 ft.lbs. (25 Nm)
Step 2: Plus 60 degrees
Step 3: Plus 60 degrees
Step 4: Plus 60 degrees
Step 5: Plus 10 degrees

1. Tighten the cylinder head bolts sequentially in three steps. NOTE: Perform each step twice. 1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.) 2nd step torque: 69 Nm (7.0 kgf-m, 51 ft. lbs.) 3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.) Use a beam-type torque wrench. When using a preset-type torque wrench, be sure to tighten slowly and not to overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt, and retighten it from the first step.