Question about Ford Crown Victoria

1 Answer

How to remove rear seat from 1954 ford customline

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 638 Answers

Some of these , you would have to get in the back seat area. and push in on the bottom front side of the seat to allow the bracket that clips into another bracket to release, do this on both sides of the seat, and seat should release and come out, the top portion of a lot of these older models, you would have to grasp the top of the seat, and push in and up and pull out, on them to release them from the brackets, installation is reverse. hope that this information has helped you.

Posted on Apr 09, 2011


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is the maximum speed of ford customline 101 hp 1952

Why do people keep asking these questions? There is no good answer because top speed depends on so many factors, such as rear axle ratio, weather, tires, state of engine tune, wear on engine, etc.

Oct 22, 2016 | Ford Cars & Trucks

1 Answer

What is the best way to remove the back seat on a 1953 ford customline

For Bottom--Push in on Front bottom (both sides) to release brackets, then lift up. For BACK--push in at top (both sides) and lift up.

Feb 18, 2015 | Ford Cars & Trucks

1 Answer

Diagram of rear brakes on 1954 Ford Custom line

My Motor's manual that covers 1954 isn't in very good shape to scan, but this video of the front brakes shows the basics, only the rear has the rear axle instead of the front spindle in the middle. They are very basic brakes.
The shoe with the shorter lining goes toward the front of the vehicle if they are different.

Feb 04, 2015 | Ford Cars & Trucks

1 Answer

How to remove gas tank from a 1954 ford f100

moved you out of JEEPs.
(drain it)
unhook all lines and hoses
then with jacks holding it up.
unstrap it (bolts)
lower jack and BINGO.

Jul 05, 2014 | Ford Cars & Trucks

1 Answer

Have a 1956 Ford Fairlane - back-up lights don't work. Can't find the switch. Know where it is located ???

both manual&auto were on the back g/gearbox housing where the rear xtension fits,fairlane??? customline

Sep 19, 2013 | Cars & Trucks

1 Answer

How do I remove the seat in a 1954 gmc truck

It just unbolts front and year and lifts out.

Jun 14, 2012 | Cars & Trucks

1 Answer

Where is chassis no 1954 ford customline

Does it have one as a lot of older american cars i import for people into spain have no chassis number from new so i make one up and stamp it in before i even start any paperwork ,they only had a metal tab under the bonnet at the front which is no good here it has to be stamped into the bodywork here so i forge it what the heck

Mar 05, 2012 | Ford Cars & Trucks

2 Answers

Chassis no for 1954 ford customline

Hi friend
The easiest place to find the VIN on your vehicle is right on the lower left corner of your dashboard. You should be able to read the number by looking through your windshield on the driver's side of your car. Check the driver's side door. The VIN might also belocated in the driver's side doorjamb or on the doorpost.


Mar 02, 2012 | Ford Cars & Trucks

1 Answer

1956 ford customline 292t,b.special;my heater will not operate & no hot air out of vents. 1956 ford customline [292 thunderbird special engine]

usually this is air trapped in the system. Try leaving the cap loose on cold start and run engine until upper hose gets hot (ie thermostat opens). That should burp air. Then keep system full as it cools down. so it uscks coolant back in as it cools. Then, tighten cap.

Jan 18, 2011 | Ford Crown Victoria Cars & Trucks

1 Answer

How to install shocks on 1956 ford sedan

They are real simple. The bottom fronts have mounting plates where the bolts go into the lower "A" leaf and the tops have a stem. On the rear its mounting bolts. There are lots of rubber bushings on them.

I had 2 1956 Fords myself, a Customline and a Crown Vic convertible. One had a 312 Interceptor engine and the other was a 292. Both had the Teapot carbs.

At one time you could get adjustable shocks or booster springs to fit around the rear shocks.

Sep 11, 2009 | Ford Five Hundred Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides