Hey everyone--after searching in vain for an entire 10 days, and absolutely REFUSING to
pay Ford's $100 diagnosis fee, and their $300 replacement suggestion
($400??), I decided to figure this out myself. And I did. Do the
following to let loose the tension that has kept your seat stuck in the
down position (though my truck is a 2008 Ford Escape, I have a strong
feeling this is the case with any vehicle):
1. Remove the seat bottoms (which are folded forward and upward against
the back of the front seats). To do this, find the bars that are
bracketed into the floor. There may or may not be a little yellow lever
on one of the two brackets. If so, flip it and slide the bar out. If
it stops, pull the other side out. Doing this should allow you to
completely remove the seat from the car. Repeat with other side.
Now you should have plenty of room to work. Move front seats forward, and you've got even more.
2. Remove your back seats entirely. (Sorry- it's a must.) For many, you will require either one or both of these:
One Torx T-50 socket to remove T-50 bolt (which bolts seat belt latches to the floor)
One Torx T-55 (which bolts the folding seat into the bracket that bolts seats to the floor).
One socket extension (tip: the extension gives you much more torque, and its easier to remove bolts) and
One a 5/8" socket. (See continuation after following tip.)
TIP: if you have a 40/60 split, you have to remove the 40 first! This
will allow you room to move around the 60 seat and its stuck belt.
Continued:
Remove bolts that bolt bracket to car floor (this is the 40 seat). I
believe there's two: 1 directly below the seat, and 1 that also bolts
the 60 seat (you'll be using the 5/8" here)-- Don't hold me to it,
though, as I've seen some different stuff. Pull seat out of the way to
avoid potential damage. NOTE: THOSE BRACKETS ARE SHARP. WATCH THE
LEATHER/SEAT MATERIAL-- AND YOUR HANDS.)
2. Remove bolts on the 60. Though the top part of your seat is down,
you should be able to the bolt that keeps the bracket to the floor
beneath where the seat cushion would be (and where the upper part of the
seat is laying flat). A ratchet would probably be best for this since
you can keep the socket in place and wind the thing completely out. I
should say here that my seat couldn't have been tighter to the floor.
If I got mine out, I'm sure you can, too.
Now here come the tricky, but verrrrry easy parts. They are vital.
1. Now that the brackets are off of the floor, the 60 seat should now
be free-floating in your hands, but tethered by the T50 bolt that is
keeping the seatbelt buckle to the floor. Remove it. Now you should be
able to remove the seat altogether. I had to bring mine inside where
it wasn't 15 degrees in my garage, but I believe you'll do these parts
in the next five minutes. Do this next:
2. TIP the 60 SEAT UPRIGHT (just like it would if things were back to
the normal operational mode). This is VITAL. If you cannot fix it with
two or three tugs from here (don't waste more time than this-- the
final part is coming), then do this next:
3. Find the latch on the back of the seat that locks onto the latch of
the car. Using two gloved fingers (or tools), press the latch inward
until it's in the LOCKED position (fooling it into thinking you've put
it up and latched into into the truck bracket).
This should have also reset the button or lever that you used to unlock
the seat in the first place. Now give your belt a tug. It should come
loose like normal.
IMPORTANT NOTE: seatbelt tensioners rely on gravity (thing momentum
during a crash) that locks the belt. If the seat is not sitting UPRIGHT
(like in normal use mode), that mechanism is going to obey gravity if
it is tilted backward or forward (which is why the seat got in the
downward position to begin with) and lock.
That's it. Bolt the seats back in, and go buy yourself $400 worth of rewards.
639 views
Usually answered in minutes!
×