Question about 1997 BMW 318

1 Answer

CYLINDER HEAD TORQUE SETTINGS BMW 318TI THANKS

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • BMW Master
  • 1,675 Answers

Hi this has to be done in 3 stages, leaving 20 to 30 minutes between tightening's they are as follows..
stage 1: 30Nm leave 30 minutes stage 2: 90 degrees turn leave 20 minutes stage 3: 90 degrees turn leave 20 minutes
you have to leave them this length of time so as not to put to much strain on the head in one go...hope this helps please vote thanks

Posted on Mar 21, 2010

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

johnz1313

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need torque settings for my cylinder head ..bmw e32 735i


Wiring, schematic, electrical diagrams, fuse diag, error codes, torque settings etc are basic contents of these online books they have here on this website www.reliable-store.com I have attached. Must check it out

Mar 12, 2018 | BMW 735i Cars & Trucks

2 Answers

Head bolt torque spec 05 bmw 4.4l


  1. Cylinder Head - AutoZone

    www.autozone.com/.../BMW-X5...05/.../Cylinder-Head/_/P-09...

    AutoZoneBMW X5 2000-05 .... Cylinder head bolt tightening sequence-4.4L & 4.6L engines. To install: ... Torque the bolts in thesequence illustrated in 3 steps as follows:.

Oct 17, 2014 | Cars & Trucks

1 Answer

Head bolt torque spec 05 bmw x5 4.4l


  1. Cylinder Head - AutoZone

    www.autozone.com/.../BMW-X5...05/.../Cylinder-Head/_/P-09...

    AutoZoneBMW X5 2000-05 .... Cylinder head bolt tightening sequence-4.4L & 4.6L engines. To install: ... Torque the bolts in thesequence illustrated in 3 steps as follows:.

Oct 17, 2014 | Cars & Trucks

1 Answer

Hiya do you know the torque settings for cylinderhead for a bmw 525d e39 2002, 6 cylinder


Per BMW AG,
Jointing torque: 80 Nm
Loosen all bolts 1/2 turn
Jointing torque 50 Nm

http://www.adrianteo.com/files/cylinder-head-torque.pdf

Oct 05, 2014 | Cars & Trucks

1 Answer

Cylinder head torque settings bmw 318i m43


Hi dear40,

The m43 engine should be similar to both the m42 and m44. The cylinder head torque settings are 22ft/lb and 90degree torque angle, and another 90 degree torque angle. Make sure to wait approximately 10minutes before performing the 2nd torque angle.

Jun 11, 2011 | 1997 BMW 318

1 Answer

I need the cylinder head torque settings for a E30 bmw 325i 1987


need cerlinderhead torque settings on a 2.7 325i bmw

May 29, 2010 | BMW 325 Cars & Trucks

1 Answer

Bmw 1998 318ti auomatic


verify the engine cooling fan runs at idle without the AC on, it should come on around just past 1/2 scale on the temp guage, do not let it overheat! these engines have aluminum cylinder heads and u can blow the head gasket out, let me know the results

Jan 11, 2009 | 1999 BMW 318 ti

1 Answer

Head bolt touqe settings


Tightening torques

Do not reuse the bolts as they may be stretched.

Cylinder head to engine block
Stage 1: 32Ft-lbs
Stage 2: +90degrees
Stage 3: +90degrees

Cylinder head to lower timing
chain cover: 89in-lbs

Nov 27, 2008 | 1992 BMW 3 Series

3 Answers

Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Jun 16, 2008 | 1992 BMW 3 Series

1 Answer

1992 BMW Cylinder head


30nm 90 degrees, 90 degrees Renew bolts!!

Jun 16, 2008 | 1996 BMW 318

Not finding what you are looking for?
1997 BMW 318 Logo

1,857 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

70 Answers

Doberman

Level 2 Expert

261 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...