My 2005 dodge grand caravn sliding door only shuts 3 quarters of the way. it opens only 1 quarter of the way. Sometimes it doesnt even open. can u help me?

Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

The arm that opens it was attached incorrectly from the sound of it. Either that or at some point the had to repair the wiring harness and the crossed the wires.

REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab

side panel.

(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

CrazyCarClub 1996 Dodge Grand Caravan Sliding Door Removal And Replacement different year but same process

from autozone.com:

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

   
   

Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.

j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.

k. Pull first rear seat belt through the access hole.

l. Remove the quarter trim panel from the vehicle.

3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).

4. Twist the blower motor out of scroll housing.

5. Disconnect the blower motor wiring connector.

6. Remove the blower motor from vehicle.


Fig. The rear blower motor is held in place by four screws
To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.
      
      
      

      Fig. Removing the trim panel to access the rear blower motor
      

   9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
   10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
   11. Pull first rear seat belt through the access hole.
   12. Remove the quarter trim panel from the vehicle.
       
3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
4. Twist the blower motor out of scroll housing.
5. Disconnect the blower motor wiring connector.
6. Remove the blower motor from vehicle.
   
   
   

   Fig. The rear blower motor is held in place by four screws
   

To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004
Blower Motor - Removal & Installation

1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
2. Remove the glove box from the instrument panel.
   
   
   Fig. The blower motor is located behind the glovebox, behind the blower motor cover
   
3. Remove the A/C-heater blower motor cover.
4. Disconnect the blower motor wiring connector.
5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
6. Remove the blower motor mounting screws.
   
   
   Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing
   
   
   
   Fig. The blower motor is secured to the housing with three small screws
   
7. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
   

To install:

1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
3. Reconnect the blower motor electrical connector.
4. Install the A/C-heater blower motor cover.
5. Install the glove box into the instrument panel.
6. Reconnect the negative battery cable. Check blower motor operation.

Auxiliary Heater and Air Conditioner
Blower Motor - Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.
      
      
      Fig. Removing the trim panel to access the rear blower motor
      
   9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
   10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
   11. Pull first rear seat belt through the access hole.
   12. Remove the quarter trim panel from the vehicle.
3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
4. Twist the blower motor out of scroll housing.
5. Disconnect the blower motor wiring connector.
6. Remove the blower motor from vehicle.
   
   
   Fig. The rear blower motor is held in place by four screws
   

To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember rated this).

You door might be gettin stuck or the is something in the door track.

Sounds like the safety switch or sensor that keeps the door from closing on passengers is faulty.

First, keep in mind that as you begin to remove these doors you run the risk of causing serious scratches to the paint and glass, so put some masking tape and/or plastic sheeting around both sides of the door (rear quarter panel and rear glass, front door and front door glass)
I would get a Haynes repair guide since that's what I have to work from and it will tell you step by step with pictures, what to do. It's not hard, but you need to get all of the attach points unhooked to be successful. Suggest you have a helper working with you to keep the door steady.