Question about 1998 Mercury Villager

1 Answer

How can I replace relay # 33 on a 1998 Mercury Villager GS

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 6 Answers

Villager quest groups.io

Posted on Jan 26, 2020

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 6 Answers

SOURCE: Mercury Villager headlight assembly diagaram for removal

This is easy. Lift the lid open. Look at the back of the sealed beam and you will see a clip and an o ring. Pull the clip up and pull wires back toward the driver's seat. Unscrew the o ring and firmly pull the bulb out toward the driver again. Note the 3 tabs on the bulb seat and realign the new bulb with those tab ( 2 bottom, 1 top). Replace with #9007 bulbs..do them both.

Posted on Dec 12, 2008

gerry bissi

  • 4388 Answers

SOURCE: Mercury Villager GS 1993

yes, ford & nissan designed van together. has nissan engine & trans.

Posted on Jan 07, 2009

Mark Egan

  • 1214 Answers

SOURCE: How do I remove the spare tire from my Mercury Villager GS

Chances are the tire has "stuck" itself to the bottom of the frame of the vehicle. This happens when a new tire comes into contact with a clean metal surface and remains there under pressure for a period of time.

If you've unscrewed the holder, and can see that the mechanism is loose from the tire, then use your foot or a 2 x 4 or pipe or something and try to wedge/lever against the tire to break it loose. Make sure you arm, leg, foot, or had is not under the tire as it will likely fall to the ground, and those things are heavy.

Posted on Jan 23, 2009

thunderalley

thunderalley

  • 432 Answers

SOURCE: it cranks but will not start

crank position sensor

Posted on Oct 04, 2009

John Jon

  • 1114 Answers

SOURCE: I need to replace the starter in a 1993 Mercury

Okay drive the van on ramps chalk rear wheels disconnect battery Under the van beside the oil pan you will see the starter motor disconnect the positive terminal and the two bolts that bolt it on the the engine lower it down by hand. Now reconnect positive terminal to the starter and any others present replace the retaining bolts tighten them .Now go up top reconnect battery and test start the van you should be good to drive now.

Posted on Dec 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We are trying to replace the electronic flasher relay in our 1999 Mercury Villager. Can you tell us where it is located?


The electronic flasher relay is located below the interior fuse block (Next to the hood release handle)

Feb 04, 2011 | 1999 Mercury Villager

1 Answer

Electric door locks malfuntioning on 1998 Mercury Villager GS


if they are self locking, there is a TSB at our site. However, it is likely one of the door lock actuators ($125) malfunctioning. usually the driver door. but try the TSB stuff first.

tascaforpparts.com will sell part at discount.

http://groups.yahoo.com/group/villagerquest/

gerry

Jan 14, 2011 | 1998 Mercury Villager

3 Answers

2000 Mercury Villager compressor wont kick on


PERHAPS IT IS JUST A BAD RELAY THAT NEEDS TO BE REPLACED. HAVE YOU TRIED TO SWAP IT WITH ANOTHER ONE IN THE FUSE BOX? THIS MAYBE THE ONLY TROUBLE. MAKE SURE THAT THE FUSE IS ALSO GOOD BEFORE THE RELAY IS REPLACED. HOPE THIS HELPS. THANKS FOR USING FIX-YA AND FOR AN HONEST RATING IN ADVANCE. BEST OF LUCK. PLEASE KEEP ME POSTED.

May 26, 2009 | 1995 Mercury Villager

2 Answers

95 Mercury Villager will not start


check/replace the starter relay switch in the relay box under the hood. The relay box is located on the front right of the engine compartment. easy fix, inexpensive part if that is the problem.

May 02, 2009 | 1995 Mercury Villager

Not finding what you are looking for?
1998 Mercury Villager Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...