20 Most Recent 2001 Mercury Villager Questions & Answers


If it's a front wheel drive motor it's on the drivers side near the steering column and is near the firewall on rear wheel drive engines it's under the windshield wiper cowl on the passenger side of the engine

2001 Mercury... | Answered on Jul 12, 2019


go to autozone & get codes read for free. report back codes before buying any parts.
Ignore knock sensor codes unless you have $6900 to throw away.

go here and join villager group

http://groups.yahoo.com/group/villagerquest/

2001 Mercury... | Answered on Jun 02, 2018


AC will not run unless the clutch is energized. You got it to engage by jumping power line. Check to see if there is a relay in the circuit that gets power to the clutch. 35PSI at 3000 rpm at 75 degrees ambient is about right. How about checking the AC on/off switch? Get a schematic and chech any component in the power trail to the clutch.

2001 Mercury... | Answered on Sep 01, 2017


need to re-remove the door panel and connect them --

2001 Mercury... | Answered on Oct 11, 2016


I guess you crawl thru and open from inside .

2001 Mercury... | Answered on May 01, 2016


code p0300 refers to random misfires---misfires detected==causes ---spark plug/s --HT lead/s ---injector/s---ignition coil/s---low compression---ECM
code p 0180 refers to fuel temperature sensor A --circuit malfunction === causes ---wiring---fuel temp sensor---ECM
code p 0325 refers to knock sensor (KS) 1 bank 1-- circuit malfunction===causes ---wiring---poor connection---KS
as the codes vary to much and are not related , the first thing I would do is to replace the ECM with a known good unit to eliminate a component failure when it gets hot
after that check wiring for injectors and fuel pump
a lot of misfires can be traced to low fuel pressure and in this case, it could be from a fuel pump failing to produce sufficient pressure when it warms up( shorting out internally)
why I suggest the ECM in the first place is the code for the knock sensor which has little to no relevance to the others and could indicate a ECM problem

2001 Mercury... | Answered on Apr 14, 2016


Check for applicable trouble codes, relating to cruise, see if that points us in the right direction?
Make sure the brake lites, work.
Other than that, about all I can tell you is to look up the wiring diagram for cruise control, check voltage and ground circuits.

2001 Mercury... | Answered on Mar 04, 2016


YOU HAVE TO GO TO THE MERCURY DEALERSHIP.SINCE YOUR VECHICLE HAS THEFT SECURITY SYSTEM. THEY HAVE TO SPECIAL MAKE KEYS BEFORE KEY SWITCH AND IGNITION IMMOBILIZER MODULE WILL WORK ALLOWING VECHICLE TO CRANK.

2001 Mercury... | Answered on Oct 25, 2015


it's flashing because there is an issue. nothing to do with an accident.

It may not deploy in accident. Get code for fault.

go here for help

http://groups.yahoo.com/group/villagerquest/

2001 Mercury... | Answered on Oct 22, 2015


Most common problem is a faulty brake switch behind the pedal.

2001 Mercury... | Answered on Oct 21, 2015


Hi there I am technology tech mechanic I work on electric and man. I come from line line of mechanics I am 5gen bc it is a check light just like for your engine optimization services there is something wrong with it and it doesn't have to be big deal could be a light bulb

2001 Mercury... | Answered on Oct 21, 2015


Try tapping it with a broom handle. Reason for this comment is that new part is made same as old. Unless you have a warranty it can fail quickly. Unsure of location of your exact type but part is usually in ductwork and much is hidden. Try Web for photos using your exact model details.

2001 Mercury... | Answered on Aug 31, 2015


remove the cover inside the tailgate to access the linkage. not a fun job but it can be done

2001 Mercury... | Answered on Jun 22, 2015


If your talking about auto headlamps, pull the two fuses in diagrams, it may stop your headlamps from draining the battery, till you can diagnose the problem. You have a lighting control module that controls the headlamps, that module may have a problem? It's hard for me to be sure, from where I'm sitting.

Can you check for applicable trouble codes, to see if a code points to lighting control module. Some of the national brand auto stores will check codes for free, if there are any.
25684618-ftcpbdyglrv1ahby2o3reo4i-2-0.jpg

2001 Mercury... | Answered on May 07, 2015


System Too Rich (Bank 1) What does that mean? Basically this means that an oxygen sensor in bank 1 detected a rich condition (too little oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1. Note: This DTC is very similar to P0175, and in fact your vehicle may show both codes at the same time. Symptoms You will more than likely not notice any drivability problems, although there may be symptoms such as a misfire. Causes A code P0172 may mean that one or more of the following has happened: The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters can cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry. There could be a vacuum leak. There could be a fuel pressure or delivery problem Possible Solutions Possible solutions include: Inspect all vacuum and PCV hoses, replace if necessary Cleanthe MAF sensor. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling Inspect fuel lines for cracks, leaks, or pinches Check the fuel pressure at the fuel rail Check the fuel injectors, they may be dirty. Use fuel injector cleaner or get them professionally cleaned/replaced. Check for an exhaust leak before the first oxygen sensor (this is unlikely to cause the problem, but it is possible)

Read more at: http://www.obd-codes.com/p0172
Copyright © OBD-Codes.com

2001 Mercury... | Answered on May 07, 2015


Look for s large square box with a plastic lid with FUSE written on it within the Engine compartment .
Alternatively probably underneath the footwell area or behind a footwell panel normally on other cars.

2001 Mercury... | Answered on Mar 07, 2015

Not finding what you are looking for?
2001 Mercury Villager Logo

241 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Villager Mercury

  • Villager Mercury

Most Popular Question

digital trouble code p0172 mean

  • Cars & Trucks
Loading...