Cars & Trucks Logo

Related Topics:

Posted on Feb 27, 2017

89 crown victoria 5.0 l efi hesitates,stumbles on acceleration

5 Related Answers

Anonymous

  • 508 Answers
  • Posted on Feb 18, 2009

SOURCE: 94 CROWN VICTORIA FUEL PUMP

Yes you can replace it. It is in the fuel tank. You will need to drain the tank and remove it to gain access to the fuel pump. A floor jack will help when lowering the fuel tank. If you fo to a dealer to do this you will be looking probably around $700.00 to replace the pump.

Ad

Anonymous

  • 28 Answers
  • Posted on Mar 19, 2009

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Anonymous

  • 33 Answers
  • Posted on Mar 23, 2009

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Anonymous

  • 93 Answers
  • Posted on Jun 09, 2009

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

john barone

  • 59 Answers
  • Posted on Jul 04, 2009

SOURCE: my horn doesn't work for my 1988 Crown Victoria

check fuse and also check the wire going to the horn and check the inside of the horn too and check the ground

I’m happy to assist further over the phone at https://www.6ya.com/expert/john_2c7bb9c157d0baa8

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

98crown victoria loss og power and stalling

Most Reported Problem Reports for the Ford Crown Victoria

repairpal.com > Problems > Ford
Verified for the Ford Crown Victoria. 4 reports. Engine Stalling and/or Hesitation on Acceleration due to Faulty Idle Air Bypass Valve. Verified for the Ford Crown ..
4helpful
2answers

What is the cylinder order on an '89 5.0? Also, what is the spark plug order?

1989 Ford Crown Victoria 5.0 liter V-8 VIN "F"

2581dec.gif

Remember rated and comment this; good luck.
1helpful
1answer

96 crown visctoria will shut off when stopping. it will crank right back up and will run till you put your foot on the break and come to a stop. what could be causing this problem. Out on the open hwy it...

Check the air filter, If it is dirty replace it, but to see if it is the problem just take it out and drive it, if it hesitates or stumbles try cleaning the throttle bottle
0helpful
1answer

2003 crown victoria NEED TO DO DIAG ENGINE LIGHT FLASHING CAR STUMBLES ON ACCELERATION RUNNING ROUGH where is the ob2 data connector

many auto parts stores have code readers to help customers out contact a few in your town to see if they can help
0helpful
1answer
1helpful
1answer

96 Crown Victoria runs rough when first started, idles smooth after a few minutes but has no acceleration before running for 20-30 minutes. Replaced the egr valve..little help, loses acceleration on the...

Ahhhh!, if only we could turn back the hands of time. Is the vehicle sending any signals like blue smoke through the exhaust, or using a lot of oil. Possibly running on after the ignition is turned off.These are all indications of high milage wear internally. Rings, bearings, etc.etc. Low oil pressure? Blinking oil light when at intersections. Any of the above?
1helpful
1answer
0helpful
1answer

1988 Ford Crown Vic Strange Idle (Getting Worse)

i am trying to install an aftermarket temperature guage with capillary tube into my 1988 crown victoria ltd 5.0 efi. where does the capillary tube mount?
0helpful
1answer

Engine is jumping

Check fuel filter and fuel pump, a clogged filter can cause loss of power during acceleration and a malfunctioning pump can cause the same thing
Not finding what you are looking for?

185 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...