How do you take out the bench seat?

Question edited for FULL 'year MAKER model'.
Question moved from Spanish car maker 'Seat' pronounced 'see-at' to correct category.

See videos and articles

https://www.google.com/search?q=1990+Mitsubishi+Montero.+remove+the+rear+bench+seat

..

check the bottom front side of bench seat.
look to see if pull out tabs '
lift.
see
https://www.autoinstruct.com.au/manufacturer/holden/ve-commodore/removing-rear-seat/
for full tutorial

You need to remove the seat bottom first to access the lower attaching points.

transfer case shift control module
Transfer Case Shift Control Module Replacement
Removal Procedure
Important: The transfer case shift control module (TCCM) is located under the drivers seat carpet. For removal purposes, access the TCCM from underneath the carpet.
Remove the drivers bucket seat or split bench seat. Refer to Front Seat Replacement - Bucket or Split Bench Seat Replacement.
Remove the left front sill plate. Refer to Front Side Door Sill Plate Replacement.
Remove the left hinge pillar. Refer to Body Hinge Pillar Trim Panel Replacement - Left Side.
Remove the left center pillar. Refer to Center Pillar Lower Trim Panel Replacement.

ok if you can see were they are bolt to the floor remove it from there and take the seat out with it,now if that seat is hold down by going in a slot and with a lever you pull or push to take out just do what you have to remove the seat

yes tighting them by hand will be enough to hold the seats saftly, you shouldnt worry about it

REMOVAL & INSTALLATION

1. Clamp the seat belts to keep them from retracting.
2. Locate and disconnect seat wiring at the connector(s).
3. Move front seats forward or back for access to the hold down hardware.
4. Put the rear seats in the stowed position.
5. On Durango 3rd row seats, lift the cushion upward and forward to floor cargo position.
6. Remove the hardware securing the seat.
7. On split bench models, lift the center seat upward to clear attachment stud
8. Remove the seat from the vehicle.

NOTE Do NOT activate the track adjusters once the fastening hardware is removed.

1. Installation is the reverse of removal.

Fig. Disconnect the wiring from under the seat




Fig. Seat track mounting hardware locations-typical




Fig. Bench seat components: seat (1), nut (2), stud (3), floor pan (4), bolt (5)-Ram




Fig. Split bench seat assembly-Ram




Fig. Bucket seat mounting components-Durango shown




Fig. Rear seat removal/installation


I hope help you with this; good luck (rated this help).

it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal

1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
   

1. Slide the bench seat forward to the center row seating position.
   

1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.
   
   
   
   
   

1. Remove the bench seat from the vehicle through the body side door opening.
   

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

The only way to remove this is to unbolt it from the sliding rails. I do believe it would still leave some parts in the rails. This seat was designed to only slide forward and not be removed. If you insist on removing it, then you must unbolt it from the sliding rails...