2000 chrysler voyager van

year? engine? po700 usually has something to do with tranny

DTC P0700: Transmission Control Module (TCM) Requested MIL Illumination
The transmission control module (TCM) uses the (GMLAN) to signal the engine control module (ECM) that the TCM is requesting malfunction indicator lamp (MIL) illumination. This happens when the TCM has determined that a failure affecting emissions has occurred in transmission control system. When the ECM receives the message from the TCM, DTC P0700 will set.
DTC P0700 can not be cleared from the ECM until the related TCM codes have been cleared.
This is something best left to a qualified repair shop , doesn't need to be the dealer ! AMMCO could fix it . This code is telling that other codes are stored in the transmission control module . Need a professional type or factory scan tool to check these . As to how much it will cost , no telling without knowing the codes in the TCM !

possible causes
Shorted or open circuit within Transmission Control Module (TCM)
- Faulty Transmission Control Module (TCM)
symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transmission shifting problems
p0700 description
The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.

Read more: http://engine-codes.com/p0700_jeep.html#ixzz2hihK6PVo

Is this P0605 and P0700? If so read on.
P0605 - Control Module Fault
Possible causes- ECM/PCM Harness power supply circuit is open or shorted
- ECM/PCM Harness ground supply circuit is open or shorted
- ECM/PCM may be faulty
P0700 CHRYSLER - Transaxle Control System (TCM) Malfunction
Possible causes- Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module
Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem

Hi there:
The DTC P0700 is a Information Code The Transaxle Control Module (TCM) that monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.
This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it, which can only be done with a diagnostic scanner. The self retreival method for chryslers with the ignition key will not pull up the specific transmission fault codes in the TCM.


Hope this helps.

P0700 DODGE - Transaxle Control System Malfunction

Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Possible causes - Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module

Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem.

P0700 DODGE Description The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.
CLEAR THE CODES AND SEE IF IT RESETS. MOST LIKELY NOT A PROBLEM

(DTC) CODE # P0700....Transmission Control System (MIL Request) Translation: Transmission Control Module (TCM) Malfunction or Failure. P0700 Information Code The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM. This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it.

I hope this helps....let me know if I can assist further !!

P0700 JEEP - Transaxle Control System Malfunction
The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Possible causes
- Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module

Tech notes: Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem. So you'll have to have the dealer or another qualified shop/technician pull the transaxle codes from the TCM and go from there.

Good luck (remember to rate this answer)

P1281 Engine Is Cold Too Long P1694 No CCD Messages Received From ECM

P0700 Transmission Control System Malfunction

For the P0700 I would check your tps sensor first to make sure it is good. This is a common failure in this vehicle which can sometimes show as a transimission malfunction.

Hope this helps, if you want alot more info about jeeps goto www.cherokeeforum.com

The P0605 is an internal failure in the transmission controller. This code sets when the tcm fails one of its internal self tests, and i think the only repair is to replace the module. P0700 is transmission control system malfunction