20 Most Recent 2000 Jeep Cherokee Questions & Answers

My 2000 jeep grand cherokee laredo won't stay charged

Trouble shooting required:
What voltage is do you get with a multi meter at the battery terminals when the vehicle is running. (looking to see the alternator is putting out the required voltage)

What voltage when it is not running & during cranking. (testing the quality of the battery)

Does the battery go flat overnight? What if you disconnect the battery overnight? (Looking to see if something is draining the battery when the vehicle is not running)

2000 Jeep... | Answered on Jan 20, 2018

Jeep Cherokee Sport 2.5 D

By power washing it you probably have water in the electrics and the electronics!! Take the Jeep to a good auto electrician and he might be able to tell you where the problem is. At least then you'll know where to start looking.
THIS is what happens when you pressure wash modern engines!!

2000 Jeep... | Answered on Jan 12, 2018

2001 XJ Sport Dash lights not working

2000 Jeep... | Posted on Dec 17, 2017 | Be the first to answer

2000 Jeep Cherokee A/C not blowing cold,

test compressor unit to make the clutch magnet is to make sure its engaging. Youtube it or google it and you'll be surprised what you find. It can be a DIY if your handy that way. And a lot less expensive as there are replacement parts for these.

2000 Jeep... | Answered on Nov 24, 2017

Replaced to electrical switchs in the ignition on

2000 Jeep... | Posted on Nov 08, 2017 | Be the first to answer

Jeep will not start. When I turn the key on after

2000 Jeep... | Posted on Aug 21, 2017 | Be the first to answer

2004 jeep grand cherokee laredo, po162, po123

162 is the O2 sensor and 123 is Throttle/Pedal Position Sensor/Switch "A" Circuit High

2000 Jeep... | Answered on Jun 18, 2017

2000 Jeep Cherokee Sport heating & a/c problem.

If your saying the blower runs intermittently, I'd start testing at the blower motor when problem is ongoing, if good voltage and ground with no blower action, suspect the blower motor. Did you use a test light to check voltage at fuses, as you can see, one fuse goes hot with the key on, the other fuse is hot all the time. The top wire in diagram for blower motor is voltage, the bottom wire is ground.
Any motor that uses brushes and the brushes are worn badly, the motor may run intermittently.
blower motor-oj0xa20ymx22hml3q4c1tsye-3-0.jpg

blower motor-oj0xa20ymx22hml3q4c1tsye-3-0.jpg

2000 Jeep... | Answered on Jun 16, 2017

If i put a lift on a 2000 cherokee 4.5in

2000 Jeep... | Posted on Apr 11, 2017 | Be the first to answer

I was driving and my battery gauge was up to 19, a

2000 Jeep... | Posted on Apr 03, 2017 | Be the first to answer

Engine will only run if gas pedal is pressed all the way

A new battery is a lot less expensive than a big tow bill, for sure. . that is how I would approach the problem

2000 Jeep... | Answered on Mar 26, 2017

The sentry key light on my 2000 Jeep cherokee stays on and the gages go up and down or don't work. All the dash lights stay on but the car runs, it did shut down twice but started back up. Help!

Probably the electric part of the ignition switch

2000 Jeep... | Answered on Feb 21, 2017

How to replace a antenna for a 2000 grand jeep laredo

same as allcars
unbolt it, remove it.
is car in USA,
some cars have electric motor up/down antennas.
if USA ,the manual is free to read, posted over 300 times
search much.?
2000 Grand Cherokee, is name, WJ jeep
see AUDIO chapter
here ,its there, under WJ

http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

2000 Jeep... | Answered on Feb 13, 2017

..Fusible Link What gauge wire do I need to use for the main fusible link in a 2000 jeep cherokee?

my guess he means , what thermal wire code to use.
they are color coded.
the fuse is bottom M1/M2 location of the PDC right"?
the problem is the OP failed to show exact wire.
my guess this is PDC question, (where are your hands/?)
fuse link A11? gas engine, right, USA?
A11 code 10 DG (dark green)
to the generator?
caused by shorted ALT or changing it with battery connected
yes, they blow.
the they have not just one engine, nor one alternator
but 124 amps the alt on 4L , with automatic. 4speed.

these are the rules. SAE.ORG

What size replacement fusible link should be used ?
The automotive service industry recommends using the same gauge and length as the blown fusible link after the cause of failure is corrected.
guide lines,
A 14-gauge wire would be protected by an 18-gauge fusible link. A 6-gauge wire would be protected by a 10-gauge link, and so on. Odd number wire gauge sizes like 19, 15, 13 and 11 are counted when sizing a link. The length of a fusible link should not exceed 9".

is the old link, still readable.
see the color
measure its size,. these tow question are first.

my jeep FSM shows it as 10 gage harness size. (M1/M2 gen slot)
so, 8 gauge thermal link is my guess. per SAE.
why not go to jeep and buy it?

2000 Jeep... | Answered on Jan 05, 2017

I have a 2000 jeep cherokee hood wont open

Have someone pull the latch and while you bounce yourself off the hood , and it should open !

2000 Jeep... | Answered on Nov 07, 2016

How do you remove the headrest on a 2000 Jeep Cherokee

factory service manual 2000. I posted the book free here 300 times.
as they say RTM , read the manual>?
Ill quote the pages for you .

"REMOVAL AND INSTALLATION
HEAD RESTRAINT SLEEVE
REMOVAL
NOTE: When replacing a head restraint sleeve, the
retaining tabs on the sleeve will be damaged during
the removal process. Check the availability of
replacement parts before servicing.
(1) Raise head restraint to the full up position.
(2) Turn head restraint lock thumbwheel to release
head restraint and pull head restraint upward to
remove from seat back.
(3) Insert head restraint sleeve extractor (special
tool 6773) (Fig. 1) and (Fig. 2) into the seat back.
(4) The retaining tabs are positioned on each side
of the sleeve, when inserting the extractor, ensure
that the flat of the collar is facing the side of the
seatback (Fig. 3).
(5) Using a small hammer, tap extractor downward
to release sleeve retaining tab.
(6) Remove extractor tool from sleeve, rotate tool
180 degrees (Fig. 4) and repeat steps 3 and 4.
(7) Remove extractor tool from sleeve and remove
sleeve from seat back."

2000 Jeep... | Answered on Oct 21, 2016

3 Answers

AC Cold air but no volumne of air flow

Please check for any blockage and in the ac duct, IF the duct is clean you need to refill the AC gas and get it serviced as the AC thens to weak over the years ........................

good luck................

2000 Jeep... | Answered on Mar 15, 2016

Where does the return line connect to on the gear box?

RTM yet? XJ jeep,
guess not
here it is . posted over 100 times.

http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

2000 Jeep... | Answered on Dec 26, 2015